8V0955102 Front Right Headlight Washer Nozzle for AUDI A3 2014

8V0955102 Front Right Headlight Washer Nozzle Product Overview

The component shown under 8V0955102 is a front right headlight washer nozzle intended for AUDI A3 2014. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A3

Compatibility for 8V0955102 should be confirmed against AUDI A3 2014 and the right installation side. The review should separate mirrored left and right items during inventory selection, compare the washer opening beside the correct headlamp, and compare the actuator orientation behind the bumper cover. Use the removed part and product photographs to match the connector and fluid inlet position where applicable, check the washer jet position relative to the headlamp lens, and check whether the bumper is standard or sport specification; finally, retain the removed component for a direct physical comparison and compare the nozzle travel direction with the vehicle-side installation.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-014 should be checked separately. For this headlight washer nozzle, compare the support flange width, inspect the molded tabs for cracks or distortion, and check the fluid inlet for storage contamination. A direct comparison with the removed part should additionally review the engagement of the cover with the nozzle stem, compare the visible bumper-side contour, and inspect narrow plastic tips before installation. Before the item is accepted, check each molded locator against the original component and review the hose spigot angle on the washer nozzle.

OE Identification and Side Confirmation

8V0955102 is the primary OE identity for this right front right headlight washer nozzle, while AD02010-014 is the internal item code. Match both references to the vehicle record, then review facelift and pre-facelift washer layouts. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-014 begins before the bumper area is disturbed: support the bumper cover while accessing the hidden actuator and confirm that no hose is pinched behind the bumper. During trial fitting, support the bumper cover while accessing the hidden actuator, confirm that no hose is pinched behind the bumper, and support the bumper cover while accessing the hidden actuator. Before returning the vehicle to service, confirm that no hose is pinched behind the bumper, support the bumper cover while accessing the hidden actuator, and confirm that no hose is pinched behind the bumper.

Receiving Inspection

When AD02010-014 arrives, receiving staff should protect the visible face again after inspection is complete, check molded tabs for whitening, cracks or transport stress, and compare left and right orientation before removing protective wrapping. Before workshop release, inspect the rear locator shape without forcing any movable section, check painted or primed surfaces under neutral lighting, inspect mounting holes for flash, blockage or edge damage, and retain the OE label until the washer system has passed its function test. Complete the inspection by ensuring that staff verify that protective plugs remain in open fluid connections, confirm that small seals or clips have not remained in the wrapping, and measure the main mounting span when two bumper versions appear similar.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8V0955102, please state the requested delivery schedule, request export-carton dimensions before freight booking, and provide the complete destination address or port. Packing instructions should separate fragile actuator bodies from heavier metal parts, state the target vehicle application, and send photographs of the removed washer part. Before dispatch, use dividers to prevent caps from rubbing each other and confirm whether caps and nozzles should be supplied as pairs.

Frequently Asked Questions

Can product photographs alone confirm 8V0955102 compatibility?

Photographs are useful for visual comparison, but the full OE number, vehicle year, bumper version, side and washer equipment must also match. For item AD02010-014, the approval should check whether the original cover is supplied separately from its support. The same item record should also confirm that the vehicle is equipped with a factory headlight washer system.

Is a sample order available for 8V0955102?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. On the listed AUDI A3 2014, technicians should use dividers to prevent caps from rubbing each other. A workshop comparison should additionally request moisture protection for sea freight.

Does the finish specification matter for 8V0955102?

Yes. A visible headlight washer nozzle may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. For the right-side order line, check the cap hinge or retaining point. The order review should further check each molded locator against the original component.

Are clips, hoses or fasteners supplied with 8V0955102?

The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. The product-specific check for 8V0955102 should retain the product label until fitment is confirmed. Receiving staff should also identify painted and unpainted variants on separate lines.

How should 8V0955102 be checked before installation?

Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. Before this headlight washer nozzle is accepted, retain the removed component for a direct physical comparison. Before approval, the buyer or technician should separate mirrored left and right items during inventory selection.