3M51-R218B08-AB Exterior Door Handle Cap without Keyhole for 2009 Ford Focus
Primary OE reference: 3M51-R218B08-AB
Cross-reference 1: 3M51-R218B08-AB
Product type: Exterior Door Handle Cap without Keyhole
Applicable vehicle: 2009 FORD Focus
Installation position: Exterior door-handle end cap without lock opening
Brand: FORD
Model: Focus
Vehicle year: 2009
Visible identification: Smooth closed cap with concealed locating tabs
Surface appearance: Painted red reference finish
Physical comparison: Compare the closed face, lower edge and clip spacing with the keyless handle-end position.
Mounting review: Compare the pivot, clips, linkage or electrical connector shown in the saved product images.
Installation preparation: Align the cap with the fixed handle base and press only where the retaining tabs are supported.
Order information: Quote 3M51-R218B08-AB, SKU FD02037-006, exterior door-handle end cap without lock opening and required quantity.
Wholesale note: State destination, packaging preference and whether matching left/right components are required.
Exterior Door Handle Cap without Keyhole Application
The exterior door handle cap without keyhole referenced by 3M51-R218B08-AB is prepared for 2009 FORD Focus and the stated exterior door-handle end cap without lock opening. Correct ordering starts with the OE code and ends with a physical back-side comparison.
Visible Profile and Component Identity
A useful recognition point is smooth closed cap with concealed locating tabs. Its visible treatment is painted red reference finish, with the carrier layout providing a second confirmation.
Product-Specific Selection Notes
Unlike a lock-side cap, this version has an uninterrupted visible surface. Its usefulness depends on the closed face matching the surrounding handle profile, so the rear locating geometry and edge radius should be checked before relying on paint colour as the identifier.
Surface and Workshop Handling
For 3M51-R218B08-AB, protect the visible painted red reference finish during bench preparation. Avoid solvents that attack moulded plastic, and do not apply paint or adhesive to the lever pivot, switch membrane or retaining clips.
Latch or Electrical Interface
Before tightening FD02037-006, inspect the latch rod or cable end, pivot pin and return spring for wear. The handle should move the latch through its full travel without side-loading the carrier or scraping the surrounding panel.
Related System Diagnosis
When FD02037-006 will not sit flush, check the reusable carrier and every clip seat for deformation before forcing 3M51-R218B08-AB into place. A distorted base or trapped paint edge can create a visible gap even when the decorative cover is correct.
Packaging for Trade Orders
For bulk packing, place FD02037-006 in an individual sleeve with the visible face separated from fasteners and adjacent handles. Mark exterior door-handle end cap without lock opening on the outer label so mirrored or different-door components remain distinguishable during warehouse picking.
Vehicle and Position Confirmation
Compare the closed face, lower edge and clip spacing with the keyless handle-end position. For 3M51-R218B08-AB, confirm 2009 production timing and the exterior door-handle end cap without lock opening designation; the wrong neighbour part may reverse a pivot, cable seat, lock opening or connector.
Automotive Replacement Part Specifications
| Product type | Exterior Door Handle Cap without Keyhole |
|---|---|
| Primary OE reference | 3M51-R218B08-AB |
| Internal item code | FD02037-006 |
| Vehicle brand | FORD |
| Model | Focus |
| Vehicle year | 2009 |
| Applicable vehicle | 2009 FORD Focus |
| Installation position | Exterior door-handle end cap without lock opening |
| Surface appearance | Painted red reference finish |
| Cross-reference numbers | 3M51-R218B08-AB |
Installation and Functional Check
Align the cap with the fixed handle base and press only where the retaining tabs are supported. Once 3M51-R218B08-AB is seated, cycle the mechanism by hand, observe its return position and make sure nearby trim is not loaded or scratched.
Receiving and Trade Supply
A trade enquiry for FD02037-006 should state 3M51-R218B08-AB, 2009 FORD Focus, exterior door-handle end cap without lock opening, the required finish and order quantity. Receiving staff can identify this exact line by comparing smooth closed cap with concealed locating tabs with the delivered item.
Frequently Asked Questions
Does 3M51-R218B08-AB fit every door?
No. This record is limited to the exterior door-handle end cap without lock opening for 2009 FORD Focus.
Which photographed cue should be reviewed first?
Start with smooth closed cap with concealed locating tabs, then turn to the concealed mounting face.
May a visually close catalogue number be used?
Only after the OE reference and physical interfaces agree; a close appearance is insufficient.
What installation result indicates correct selection?
The mechanism should release cleanly, return without drag and sit evenly against the surrounding panel.
What information belongs on the purchase order?
List FD02037-006, 3M51-R218B08-AB, FORD Focus, year range, installed position and quantity.
