3M51-R218A14-ABXWAA Keyhole Door Handle Cap for 2005 Ford Focus
Primary OE reference: 3M51-R218A14-ABXWAA
Cross-reference 1: 3M51-R218A14-ABXWAA
Cross-reference 2: 1772033
Product type: Exterior Door Handle Cap with Keyhole
Applicable vehicle: 2005 FORD Focus
Installation position: Exterior lock-side door-handle cap
Brand: FORD
Model: Focus
Vehicle year: 2005
Visible identification: Compact handle end cover with round lock opening
Surface appearance: Colour-coded cap with key-cylinder aperture
Physical comparison: Check paint code, aperture position and the shape of all rear retention points.
Mounting review: Compare the pivot, clips, linkage or electrical connector shown in the saved product images.
Installation preparation: Position the cap around the cylinder without scraping the painted edge, then engage the clips squarely.
Order information: Quote 3M51-R218A14-ABXWAA, SKU FD02037-011, exterior lock-side door-handle cap and required quantity.
Wholesale note: State destination, packaging preference and whether matching left/right components are required.
Exterior Door Handle Cap with Keyhole Application
For the 2005 FORD Focus, 3M51-R218A14-ABXWAA is catalogued as a exterior door handle cap with keyhole at the exterior lock-side door-handle cap. Door position, operating method and rear-side construction define the correct variant.
Visible Profile and Component Identity
This item’s distinguishing form is compact handle end cover with round lock opening. The pictured colour-coded cap with key-cylinder aperture helps separate it from neighbouring catalogue versions.
Product-Specific Selection Notes
The XWAA suffix identifies a finished variant of the keyed handle cover. Surface colour alone is not sufficient: compare the cylinder opening offset and underside clips with the original. Keep the painted face isolated from loose hardware during workshop storage.
Surface and Workshop Handling
For 3M51-R218A14-ABXWAA, protect the visible colour-coded cap with key-cylinder aperture during bench preparation. Avoid solvents that attack moulded plastic, and do not apply paint or adhesive to the lever pivot, switch membrane or retaining clips.
Latch or Electrical Interface
Before tightening FD02037-011, inspect the latch rod or cable end, pivot pin and return spring for wear. The handle should move the latch through its full travel without side-loading the carrier or scraping the surrounding panel.
Related System Diagnosis
When FD02037-011 will not sit flush, check the reusable carrier and every clip seat for deformation before forcing 3M51-R218A14-ABXWAA into place. A distorted base or trapped paint edge can create a visible gap even when the decorative cover is correct.
Packaging for Trade Orders
For bulk packing, place FD02037-011 in an individual sleeve with the visible face separated from fasteners and adjacent handles. Mark exterior lock-side door-handle cap on the outer label so mirrored or different-door components remain distinguishable during warehouse picking.
Vehicle and Position Confirmation
Check paint code, aperture position and the shape of all rear retention points. For 3M51-R218A14-ABXWAA, confirm 2005 production timing and the exterior lock-side door-handle cap designation; the wrong neighbour part may reverse a pivot, cable seat, lock opening or connector.
Automotive Replacement Part Specifications
| Product type | Exterior Door Handle Cap with Keyhole |
|---|---|
| Primary OE reference | 3M51-R218A14-ABXWAA |
| Internal item code | FD02037-011 |
| Vehicle brand | FORD |
| Model | Focus |
| Vehicle year | 2005 |
| Applicable vehicle | 2005 FORD Focus |
| Installation position | Exterior lock-side door-handle cap |
| Surface appearance | Colour-coded cap with key-cylinder aperture |
| Cross-reference numbers | 3M51-R218A14-ABXWAA / 1772033 |
Installation and Functional Check
Position the cap around the cylinder without scraping the painted edge, then engage the clips squarely. Once 3M51-R218A14-ABXWAA is seated, cycle the mechanism by hand, observe its return position and make sure nearby trim is not loaded or scratched.
Receiving and Trade Supply
A trade enquiry for FD02037-011 should state 3M51-R218A14-ABXWAA / 1772033, 2005 FORD Focus, exterior lock-side door-handle cap, the required finish and order quantity. Receiving staff can identify this exact line by comparing compact handle end cover with round lock opening with the delivered item.
Frequently Asked Questions
Which vehicle record accompanies 3M51-R218A14-ABXWAA?
2005 FORD Focus is the recorded application, with installation at the exterior lock-side door-handle cap.
What visual detail separates this item?
Compact handle end cover with round lock opening is the principal recognition point shown by the photographs.
Why must the installation position be stated?
Adjacent doors and left/right locations can use different hidden carriers even with similar outer styling.
How should operation be verified?
Test release, lever return and trim clearance several times before the door or tailgate is fully reassembled.
Which data speeds up a wholesale quote?
Use SKU FD02037-011, OE 3M51-R218A14-ABXWAA, application, required quantity, delivery market and colour or finish request.
