6GPT-14A076-AF Fuse Box Upper Cover for 2011 Ford Mondeo
Primary OE reference: 6GPT-14A076-AF
Cross-reference 1: 6GPT-14A076-AF
Product type: Fuse Box Upper Cover
Applicable vehicle: 2011 FORD Mondeo
Installation position: Engine-bay fuse and relay enclosure
Brand: FORD
Model: Mondeo
Vehicle year: 2011
Identification detail: Mondeo enclosure lid with moulded ribs, catches and perimeter return
Fitment basis: Confirm 6GPT-14A076-AF, connector or latch layout, mounting points and enclosure profile.
Installation guidance: Dry-fit the component, engage every locating tab and confirm cables or seals are not trapped.
Purchase reference: Quote SKU FD02040-012, OE number, vehicle application and required quantity.
6GPT-14A076-AF Fuse Box Upper Cover Overview
For the 2011 FORD Mondeo, 6GPT-14A076-AF corresponds to this fuse box upper cover. This lid is catalogued for the 2011 Mondeo electrical box and should be matched by its catch pattern rather than colour alone.
Component Identification
Before replacement, compare Mondeo enclosure lid with moulded ribs, catches and perimeter return. A correct match should sit naturally at the engine-bay fuse and relay enclosure without forcing nearby harnesses, trim or brackets.
Enclosure and Retention Details
Clean the mating rim and identify every clip before fitting 6GPT-14A076-AF. Replace damaged retainers; uneven engagement can leave the enclosure open to moisture or vibration.
Workshop Stock Control
For workshop stock control, label FD02040-012 with 6GPT-14A076-AF, FORD Mondeo and the exact installation area. Keep the component separated from visually similar electrical housings.
Closure and Service Access
After installation, run a hand check around the complete edge. The lid should close evenly, release with the intended service motion and avoid contact with wires beneath it.
Mondeo Electrical Bay Service Context
The 6GPT-series cover belongs to an earlier Mondeo power-distribution layout. When comparing dismantled stock, note the position of the broad reinforcing channels, the corner reliefs and the direction in which the catches release. The correct lid should leave access to the designated cable route and should not press against relay tops. If the original housing has heat distortion, investigate terminal resistance and repair the electrical cause before installing a replacement cover.
Automotive Replacement Part Specifications
| Product type | Fuse Box Upper Cover |
|---|---|
| Primary OE reference | 6GPT-14A076-AF |
| Internal item code | FD02040-012 |
| Vehicle brand | FORD |
| Model | Mondeo |
| Vehicle year | 2011 |
| Applicable vehicle | 2011 FORD Mondeo |
| Installation position | Engine-bay fuse and relay enclosure |
| Identification detail | Mondeo enclosure lid with moulded ribs, catches and perimeter return |
| Cross-reference numbers | 6GPT-14A076-AF |
Packaging and Wholesale Supply
Protect the connector, clips, sealing rim and moulded corners during packing. Mark the carton with FD02040-012, 6GPT-14A076-AF and Engine-bay fuse and relay enclosure so warehouse staff can distinguish the correct variant.
Frequently Asked Questions
What does 6GPT-14A076-AF identify?
6GPT-14A076-AF identifies the listed fuse box upper cover for the 2011 FORD Mondeo.
How should FD02040-012 be matched?
Compare the OE reference, Mondeo enclosure lid with moulded ribs, catches and perimeter return, installation location and all concealed attachment details.
Is visual similarity enough for selection?
No. Similar electrical covers and sensors can use different connectors, clips, seals or mounting geometry.
What should be checked after fitting?
Confirm full tab engagement, even edge seating and clearance around the wiring harness.
What details are needed for a trade quotation?
Provide 6GPT-14A076-AF, SKU FD02040-012, vehicle model, model year, destination and quantity.
