4M0807754D-1 Front Right Headlight Washer Nozzle Cover for AUDI Q7 2020
Primary OE reference: 4M0807754D-1
Cross-reference number 1: 4M0 807 754D-1
Cross-reference number 2: 4M0807754D-1
Cross-reference number 3: 4M0807754D1
Product type: Front Right Headlight Washer Nozzle Cover
Vehicle application: AUDI Q7 2020
Installation position: Front bumper / headlight washer area
Side: Right
Brand: AUDI
Model: Q7
Model year: 2020
Product function: Closes the bumper washer opening and restores the visible exterior contour around the headlamp.
Fitment check: Confirm the complete OE number, model year, bumper specification and left/right position before ordering.
Supply scope: The supplied components follow the product photographs; clips, hoses, seals and fasteners are included only when shown or separately confirmed.
Surface finish: Compare the visible colour and texture with the original part; painting may be required before final installation.
Internal item code: AD02010-101
Quotation information: Send the OE number, vehicle model/year, required side, quantity and delivery destination for an application-specific quotation.
4M0807754D-1 Front Right Headlight Washer Nozzle Cover Product Overview
The component shown under 4M0807754D-1 is a front right headlight washer nozzle cover intended for AUDI Q7 2020. The visible cover closes the bumper opening around the washer unit and follows the surrounding bumper contour when the nozzle is retracted. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.
Fitment and Washer-System Application for Q7
Compatibility for 4M0807754D-1 should be confirmed against AUDI Q7 2020 and the right installation side. The review should review facelift and pre-facelift washer layouts, match the mounting pattern around the bumper aperture, and retain the removed component for a direct physical comparison. Use the removed part and product photographs to verify that the OE reference is not for the opposite side, check regional variations in headlamp-cleaning equipment, and match the connector and fluid inlet position where applicable; finally, check whether the original cover is supplied separately from its support and confirm the front bumper option before ordering.
Headlight Washer Nozzle Cover Function and Design Notes
The visible and hidden interfaces of AD02010-101 should be checked separately. For this headlight washer nozzle cover, check each molded locator against the original component, review any paint-preparation requirement before fitting, and compare the outer surface profile with the bumper opening. A direct comparison with the removed part should additionally inspect narrow plastic tips before installation, check the bumper-facing surface for transport marks, and review the bracket stiffness and screw seats. Before the item is accepted, compare the visible bumper-side contour and inspect the base bracket around every locating slot.
OE Identification and Side Confirmation
4M0807754D-1 is the primary OE identity for this right front right headlight washer nozzle cover, while AD02010-101 is the internal item code. Match both references to the vehicle record, then check regional variations in headlamp-cleaning equipment. Do not substitute the mirrored side merely because the visible cover shape appears similar.
Installation and System Testing Guidance
Workshop preparation for AD02010-101 begins before the bumper area is disturbed: tighten bracket hardware only after alignment and test for drips after the washer pump stops. During trial fitting, transfer reusable clips only after checking their condition, verify that the cap remains attached through a full washer cycle, and verify that the cover closes without rubbing the bumper. Before returning the vehicle to service, disconnect the fluid hose without twisting the plastic spigot, support the bumper cover while accessing the hidden actuator, and use hand pressure rather than levering narrow plastic tabs.
Receiving Inspection
When AD02010-101 arrives, receiving staff should inspect the visible cover face for scratches or pressure marks, inspect projecting pins before placing the item on a hard bench, and compare connector depth and hose angle with the retained original part. Before workshop release, check molded tabs for whitening, cracks or transport stress, review the production finish against the approved sample, inspect mounting holes for flash, blockage or edge damage, and confirm the nozzle outlet is clean and unobstructed. Complete the inspection by ensuring that staff measure the main mounting span when two bumper versions appear similar, confirm the bumper-facing edge has not been compressed in transit, and review the hose spigot for impact damage or distortion.
Product Technical Specifications
| Product type | Front Right Headlight Washer Nozzle Cover |
|---|---|
| Primary OE reference | 4M0807754D-1 |
| Cross-reference numbers | 4M0 807 754D-1 4M0807754D-1 4M0807754D1 |
| Internal item code | AD02010-101 |
| Vehicle brand | AUDI |
| Vehicle model | Q7 |
| Model year | 2020 |
| Installation position | Front bumper / headlamp washer area |
| Side / orientation | Right |
| Applicable vehicle | AUDI Q7 2020 |
Wholesale Supply and Protective Packing
For a quotation or repeat order of 4M0807754D-1, please use dividers to prevent caps from rubbing each other, plug open fluid connections during packing, and use dividers to prevent caps from rubbing each other. Packing instructions should plug open fluid connections during packing, use dividers to prevent caps from rubbing each other, and plug open fluid connections during packing. Before dispatch, use dividers to prevent caps from rubbing each other and plug open fluid connections during packing.
Frequently Asked Questions
Which vehicle application is listed for 4M0807754D-1?
4M0807754D-1 is listed for AUDI Q7 2020. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. For item AD02010-101, the approval should compare the actuator orientation behind the bumper cover. The same item record should also verify nearby parking-sensor or trim interfaces.
Why must left and right versions of 4M0807754D-1 be distinguished?
Headlight washer components are normally side-specific. Their bumper contours, hose angles, tabs and nozzle directions should not be assumed interchangeable. On the listed AUDI Q7 2020, technicians should review the hose spigot angle on the washer nozzle. A workshop comparison should additionally review any paint-preparation requirement before fitting.
How should 4M0807754D-1 be packed for export?
The front right headlight washer nozzle cover should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. For the right-side order line, protect each nozzle outlet from dust during transit. The order review should further use dividers to prevent caps from rubbing each other.
Is a sample order available for 4M0807754D-1?
Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. The product-specific check for 4M0807754D-1 should protect each nozzle outlet from dust during transit. Receiving staff should also check carton labels at receiving.
Is 4M0807754D-1 a complete headlight washer system?
No. This listing covers the pictured headlight washer nozzle cover. The pump, reservoir, hoses, opposite-side parts and headlamp assembly are not included unless shown in the photographs. Before this headlight washer nozzle cover is accepted, protect hose spigots and projecting tabs. Before approval, the buyer or technician should include the full OE reference on the purchase order.
