8K0955275C Front Left Headlight Washer Nozzle Cover for AUDI A4 2013
Primary OE reference: 8K0955275C
Cross-reference number 1: 8K0 955 275C
Cross-reference number 2: 8K0955275C
Product type: Front Left Headlight Washer Nozzle Cover
Vehicle application: AUDI A4 2013
Installation position: Front bumper / headlight washer area
Side: Left
Brand: AUDI
Model: A4
Model year: 2013
Product function: Closes the bumper washer opening and restores the visible exterior contour around the headlamp.
Fitment check: Confirm the complete OE number, model year, bumper specification and left/right position before ordering.
Supply scope: The supplied components follow the product photographs; clips, hoses, seals and fasteners are included only when shown or separately confirmed.
Surface finish: Compare the visible colour and texture with the original part; painting may be required before final installation.
Internal item code: AD02010-027
Quotation information: Send the OE number, vehicle model/year, required side, quantity and delivery destination for an application-specific quotation.
8K0955275C Front Left Headlight Washer Nozzle Cover Product Overview
The component shown under 8K0955275C is a front left headlight washer nozzle cover intended for AUDI A4 2013. The visible cover closes the bumper opening around the washer unit and follows the surrounding bumper contour when the nozzle is retracted. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.
Fitment and Washer-System Application for A4
Compatibility for 8K0955275C should be confirmed against AUDI A4 2013 and the left installation side. The review should compare the complete OE marking with the removed washer component, compare the actuator orientation behind the bumper cover, and confirm the front bumper option before ordering. Use the removed part and product photographs to compare the hose connection or cover hinge with the original part, compare every tab, clip seat and locating shoulder, and review facelift and pre-facelift washer layouts; finally, compare the nozzle travel direction with the vehicle-side installation and confirm that the vehicle is equipped with a factory headlight washer system.
Headlight Washer Nozzle Cover Function and Design Notes
The visible and hidden interfaces of AD02010-027 should be checked separately. For this headlight washer nozzle cover, inspect the rear reinforcement ribs, check the cap hinge or retaining point, and review the engagement of the cover with the nozzle stem. A direct comparison with the removed part should additionally compare the cap-to-support engagement method, inspect the hose connector for ovality, and check whether the visible part requires painting. Before the item is accepted, review the hose spigot angle on the washer nozzle and compare the support flange width.
OE Identification and Side Confirmation
8K0955275C is the primary OE identity for this left front left headlight washer nozzle cover, while AD02010-027 is the internal item code. Match both references to the vehicle record, then confirm the destination-market equipment specification. Do not substitute the mirrored side merely because the visible cover shape appears similar.
Installation and System Testing Guidance
Workshop preparation for AD02010-027 begins before the bumper area is disturbed: disconnect the fluid hose without twisting the plastic spigot and transfer reusable clips only after checking their condition. During trial fitting, trial-fit the component before final fastening, align the cover flush with the bumper surface, and route the washer hose away from sharp edges. Before returning the vehicle to service, confirm that the nozzle extends and retracts freely, check the system for leaks after reconnection, and test the spray direction before returning the vehicle.
Receiving Inspection
When AD02010-027 arrives, receiving staff should check the actuator body for straightness before trial installation, inspect the fluid passage only with clean, non-damaging tools, and verify the cover contour against the approved product photograph. Before workshop release, confirm the bumper-facing edge has not been compressed in transit, inspect projecting pins before placing the item on a hard bench, protect the visible face again after inspection is complete, and inspect the rear locator shape without forcing any movable section. Complete the inspection by ensuring that staff retain the OE label until the washer system has passed its function test, measure the main mounting span when two bumper versions appear similar, and inspect the visible cover face for scratches or pressure marks.
Product Technical Specifications
| Product type | Front Left Headlight Washer Nozzle Cover |
|---|---|
| Primary OE reference | 8K0955275C |
| Cross-reference numbers | 8K0 955 275C 8K0955275C |
| Internal item code | AD02010-027 |
| Vehicle brand | AUDI |
| Vehicle model | A4 |
| Model year | 2013 |
| Installation position | Front bumper / headlamp washer area |
| Side / orientation | Left |
| Applicable vehicle | AUDI A4 2013 |
Wholesale Supply and Protective Packing
For a quotation or repeat order of 8K0955275C, please request export-carton dimensions before freight booking, check carton labels at receiving, and confirm pallet requirements for larger quantities. Packing instructions should confirm sample approval before mass shipment, identify painted and unpainted variants on separate lines, and include the full OE reference on the purchase order. Before dispatch, plug open fluid connections during packing and state the target vehicle application.
Frequently Asked Questions
Is workshop installation recommended for 8K0955275C?
Yes. A qualified workshop can access the bumper area on the A4, transfer hoses or clips safely and test the washer system for correct operation and leaks. For item AD02010-027, the approval should reconfirm the OE number before discarding the packaging. The same item record should also verify that the cover closes without rubbing the bumper.
Should the washer system be tested after fitting 8K0955275C?
Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. On the listed AUDI A4 2013, technicians should verify that the cover closes without rubbing the bumper. A workshop comparison should additionally check the headlamp lens receives an even spray.
Are clips, hoses or fasteners supplied with 8K0955275C?
The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. For the left-side order line, confirm the preferred incoterm. The order review should further use dividers to prevent caps from rubbing each other.
What should be inspected when 8K0955275C arrives?
Check the item label, side, contour, tabs, fluid connection, supplied components and carton condition before fitting or discarding the packaging. The product-specific check for 8K0955275C should check molded tabs for whitening, cracks or transport stress. Receiving staff should also measure the main mounting span when two bumper versions appear similar.
Does the finish specification matter for 8K0955275C?
Yes. A visible headlight washer nozzle cover may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. Before this headlight washer nozzle cover is accepted, compare the retracted position with the bumper surface. Before approval, the buyer or technician should check the joint between the visible cap and hidden support.
