71102-TBT-H50 Front Right Fog Light Bezel for HONDA Crider 2022

71102-TBT-H50 Front Right Fog Light Bezel Product Overview

The product shown under 71102-TBT-H50 is a front right fog light bezel intended for HONDA Crider 2022. Check the right orientation, lamp opening, mounting tabs and high-specification specification against the original component.

Fitment and Application for Crider

When preparing a Crider bumper repair, check the nearby lamp opening, confirm the bumper position, and review facelift styling. Before final installation, match the outer contour, check the vehicle build date, and compare the original grille section.

During comparison with the original lamp surround, review the bezel orientation, compare the full OE marking, and check the nearby lamp opening. During receiving inspection, confirm the surface finish, confirm the model year, and confirm the bumper position.

For replacement in the right front area, inspect the lamp aperture size, match the locating-slot layout, and review the bezel orientation. Before the quotation is confirmed, match the outer contour, check the nearby lamp opening, and verify the mounting side.

Front Right Fog Light Bezel Design and Replacement Notes

Before the removed bezel is discarded, compare the original edge profile, compare the centre alignment, and check the bumper transition. For a repeat wholesale order, review narrow bezel ends, measure the original length, and review nearby cover openings.

During an OE-led review for HD02008-130, check the bumper transition, confirm decorative finish details, and check the adjoining gap. While reviewing the supplied photographs, review locator direction, check the lamp interface, and review fastening slots.

For wholesale selection of 71102-TBT-H50, measure the original length, compare transferred hardware, and check the adjoining gap. Before final installation, review narrow bezel ends, inspect reinforcement ribs, and compare the surface texture.

Application-Specific Identification Notes

Before a replacement is packed with 71102-TBT-H50 on the Crider 2022: check the vehicle build date. The HD02008-130 sample for the right side should inspect reinforcement ribs. For HONDA identification, 71102-TBT-H50 also requires technicians to confirm the fitting direction. A buyer quoting HD02008-130 should request export quotation terms for the HONDA Crider 2022 order.

For application-specific sourcing with 71102-TBT-H50 on the Crider 2022: inspect the removed bezel. The HD02008-130 sample for the right side should check the adjoining gap. For HONDA identification, 71102-TBT-H50 also requires technicians to confirm an evenly seated fit. A buyer quoting HD02008-130 should include the complete OE reference for the HONDA Crider 2022 order.

When the bumper opening is reviewed with 71102-TBT-H50 on the Crider 2022: review the bezel orientation. The HD02008-130 sample for the right side should check the bumper transition. For HONDA identification, 71102-TBT-H50 also requires technicians to support the bumper cover evenly. A buyer quoting HD02008-130 should include the complete OE reference for the HONDA Crider 2022 order.

A trim-level comparison requires with 71102-TBT-H50 on the Crider 2022: check adjacent bumper parts. The HD02008-130 sample for the right side should review the outer-edge shape. For HONDA identification, 71102-TBT-H50 also requires technicians to avoid bending moulded tabs. A buyer quoting HD02008-130 should request export quotation terms for the HONDA Crider 2022 order.

Installation Guidance

When preparing a Crider bumper repair, check lamp-to-bezel clearance, confirm the finished bumper gap, and check adjacent panel gaps. When checking the bumper opening, check the final perimeter, trial-fit the bezel without force, and inspect each screw point.

During comparison with the original lamp surround, confirm an evenly seated fit, protect exposed panel edges, and check lamp-to-bezel clearance. At the workshop preparation stage, confirm every locator engages, inspect damaged mounting points, and protect nearby painted surfaces.

For replacement in the right front area, support the bumper cover evenly, align the lamp opening first, and check adjacent panel gaps. For a repeat wholesale order, retain the removed bezel for comparison, confirm the fitting direction, and check the final perimeter.

Product Technical Specifications

Wholesale Supply and Packing

Before the removed bezel is discarded, request protective inner wrapping, state annual purchasing volume, and state the target vehicle. Before clips or hardware are transferred, protect projecting locator tabs, provide the delivery country, and confirm the packing method.

During an OE-led review for HD02008-130, request supported carton packing, protect projecting locator tabs, and support the bezel during transit. During the physical comparison, inspect receiving condition, retain the product label, and confirm sample requirements.

For wholesale selection of 71102-TBT-H50, state the target vehicle, confirm the delivery schedule, and support the bezel during transit. When checking the bumper opening, state annual purchasing volume, include the complete OE reference, and review carton edge protection.

Frequently Asked Questions

What should be inspected when 71102-TBT-H50 arrives?

Check the label, contour, surface finish, lamp aperture, tabs, mounting points and carton condition before installation or disposal of the packaging. For Crider, compare the original grille section, inspect the moulded face, align the lamp opening first, and inspect receiving condition before installation or quotation.

Where is 71102-TBT-H50 installed?

The listed front right fog light bezel belongs in the right front bumper area. An opposite-side or different-trim bezel may use another outline and tab arrangement. For Crider, review the bezel orientation, measure the original length, confirm an evenly seated fit, and request protective inner wrapping before installation or quotation.

What details should accompany a 71102-TBT-H50 quotation request?

Send the complete OE reference, vehicle information, mounting side, original-part photographs, quantity and destination so the application can be reviewed. For Crider, confirm the surface finish, compare the centre alignment, confirm every locator engages, and review carton edge protection before installation or quotation.

Why must the left and right versions of 71102-TBT-H50 be distinguished?

Left and right bezels are normally mirror-specific. Their curves, screw points and locator tabs should not be assumed interchangeable. For Crider, check adjacent bumper parts, compare mounting-hole height, verify the lamp remains centred, and include the complete OE reference before installation or quotation.

Is workshop installation recommended for 71102-TBT-H50?

Yes. A workshop can inspect damaged bumper mounts on the Crider, align the lamp opening and avoid forcing a bezel intended for another trim level. For Crider, match the locating-slot layout, compare the surface texture, inspect each screw point, and state annual purchasing volume before installation or quotation.

Request a Quote

Send the complete OE reference 71102-TBT-H50, vehicle details, mounting side, quantity and destination. Yongshang Auto can review the application before preparing a product-specific export quotation.