CN15-15K273-AD Rear Bumper Light for FORD EcoSport 2013 Left
Primary OE reference: CN15-15K273-AD
Product type: Rear Bumper Light
Applicable vehicle: FORD EcoSport 2013
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: FORD
Model: EcoSport
Vehicle year: 2013
Bumper interface: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Product function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Connector review: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Fitting note: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
Trade-order details: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
CN15-15K273-AD Rear Bumper Light Overview
This product is listed for FORD EcoSport 2013 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Before approving the EcoSport part for packing, align each locating tab with the matching slot before applying hand pressure to reduce clip damage during a no-force trial installation.
Bumper Opening and Vehicle Match
Review the corner radius, edge return and rear fastening points against the original bumper opening.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Before fitting the left unit, check whether the original component uses a separate retainer or an integral locking tab to prevent a visually similar version from sitting proud of the bumper.
While the FORD bumper opening is accessible, verify the fastener direction and the shape of the concealed support frame before the packaging and carton marking are finalized.
Lens Construction and Powered Variants
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Protect the exposed face from tools and fasteners while the bumper liner is open for access.
During comparison of the FORD rear component, protect the visible surface until the full perimeter gap has been accepted before inner liners make the rear attachment points difficult to inspect.
For a repeat order of the left version, review the reflector texture and lens colour in neutral workshop light so the visible gap remains even after every retaining point is engaged.
Mounting and Final Verification
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.
On the 2013 EcoSport bumper layout, record the approved side and vehicle application for repeat-order identification so the lens and housing are supported without distortion.
At the workshop selection stage for EcoSport, confirm that the cable exit, where fitted, clears the bumper reinforcement so a passive reflector is not confused with an illuminated assembly.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | CN15-15K273-AD |
| Cross-reference numbers | CN15-15K273-AD |
| Internal item code | FD04004-005 |
| Vehicle brand | FORD |
| Vehicle model | EcoSport |
| Model year | 2013 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
At the left rear-bumper position, confirm that any connector seal remains square when the housing is fully seated to verify that the photographed configuration matches the vehicle in the workshop.
When reviewing the 2013 vehicle, use the opposite-side component only as an alignment reference, not as an interchange part to avoid contact with wiring, body edges or hot exhaust components.
Frequently Asked Questions
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Request a Product-Specific Quote
The sales team can check whether accessories shown in the photograph are part of the requested scope.
