92406-3X210 Rear Bumper Light for HYUNDAI Elantra 2014 Right
Primary OE reference: 92406-3X210
Product type: Rear Bumper Light
Applicable vehicle: HYUNDAI Elantra 2014
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: HYUNDAI
Model: Elantra
Vehicle year: 2014
Fitment evidence: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Optical configuration: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical interface: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Final alignment: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.
Bulk supply: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.
92406-3X210 Rear Bumper Light Overview
This product is listed for HYUNDAI Elantra 2014 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
During comparison of the HYUNDAI rear component, verify the fastener direction and the shape of the concealed support frame so the approved product can be picked consistently in a mixed wholesale order.
Bumper Opening and Vehicle Match
Review the corner radius, edge return and rear fastening points against the original bumper opening.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
For a repeat order of the right version, protect the visible surface until the full perimeter gap has been accepted so hidden brackets are not loaded or bent during installation.
On the 2014 Elantra bumper layout, review the reflector texture and lens colour in neutral workshop light to preserve access for a final electrical test where a lamp circuit is present.
Lens Construction and Powered Variants
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
At the workshop selection stage for Elantra, record the approved side and vehicle application for repeat-order identification to reduce clip damage during a no-force trial installation.
At the right rear-bumper position, confirm that the cable exit, where fitted, clears the bumper reinforcement to prevent a visually similar version from sitting proud of the bumper.
Mounting and Final Verification
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.
When reviewing the 2014 vehicle, confirm that any connector seal remains square when the housing is fully seated before the packaging and carton marking are finalized.
For the HYUNDAI Elantra application, use the opposite-side component only as an alignment reference, not as an interchange part before inner liners make the rear attachment points difficult to inspect.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 92406-3X210 |
| Cross-reference numbers | 92406-3X210 |
| Internal item code | HY04004-006 |
| Vehicle brand | HYUNDAI |
| Vehicle model | Elantra |
| Model year | 2014 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
For this Elantra body configuration, compare the outer lens edge with the moulded bumper recess so the visible gap remains even after every retaining point is engaged.
Before approving the Elantra part for packing, inspect the lower valance and nearby exhaust trim for adequate operating clearance so the lens and housing are supported without distortion.
Frequently Asked Questions
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Request a Product-Specific Quote
A product-specific quotation can be prepared after the vehicle, side and destination are confirmed.
