92405-C7000 Rear Bumper Light for HYUNDAI i20 2016 Left
Primary OE reference: 92405-C7000
Product type: Rear Bumper Light
Applicable vehicle: HYUNDAI i20 2016
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: HYUNDAI
Model: i20
Vehicle year: 2016
Bumper interface: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Product function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Connector review: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Fitting note: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Production date and regional bumper specification should be reviewed when several near-identical versions are available.
Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
Trade-order details: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
92405-C7000 Rear Bumper Light Overview
This product is listed for HYUNDAI i20 2016 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.
For this i20 body configuration, confirm that any connector seal remains square when the housing is fully seated before any modification is made to the bumper or replacement part.
Vehicle Fitment and Bumper Interface
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Use the removed component as the physical reference for outer shape, housing projection and clip location.
Before approving the i20 part for packing, use the opposite-side component only as an alignment reference, not as an interchange part before deciding whether original hardware is suitable for reuse.
Before fitting the left unit, compare the outer lens edge with the moulded bumper recess because facelift bumpers can retain the same vehicle name with different apertures.
Reflector, Lens and Electrical Configuration
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
While the HYUNDAI bumper opening is accessible, inspect the lower valance and nearby exhaust trim for adequate operating clearance so left- and right-hand stock cannot be mixed during consolidation.
During comparison of the HYUNDAI rear component, check the rear housing projection against the space behind the bumper skin so the approved product can be picked consistently in a mixed wholesale order.
Installation and Functional Check
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
For a repeat order of the left version, compare the bumper corner radius with the product face from more than one viewing angle so hidden brackets are not loaded or bent during installation.
On the 2016 i20 bumper layout, align each locating tab with the matching slot before applying hand pressure to preserve access for a final electrical test where a lamp circuit is present.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 92405-C7000 |
| Cross-reference numbers | 92405-C7000 |
| Internal item code | HY04004-053 |
| Vehicle brand | HYUNDAI |
| Vehicle model | i20 |
| Model year | 2016 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
At the workshop selection stage for i20, check whether the original component uses a separate retainer or an integral locking tab to reduce clip damage during a no-force trial installation.
At the left rear-bumper position, verify the fastener direction and the shape of the concealed support frame to prevent a visually similar version from sitting proud of the bumper.
Frequently Asked Questions
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Request a Product-Specific Quote
Provide the expected order quantity to receive a trade-oriented packing and supply proposal.
