92405-4Z500 Rear Bumper Light for HYUNDAI Santa Fe 2016 Left
Primary OE reference: 92405-4Z500
Product type: Rear Bumper Light
Applicable vehicle: HYUNDAI Santa Fe 2016
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: HYUNDAI
Model: Santa Fe
Vehicle year: 2016
Shape and clips: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Rear visibility role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Powered-version check: Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Workshop guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.
Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.
Quotation details: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.
Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
92405-4Z500 Rear Bumper Light Overview
This product is listed for HYUNDAI Santa Fe 2016 at the left rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
Before approving the Santa Fe part for packing, compare the outer lens edge with the moulded bumper recess before deciding whether original hardware is suitable for reuse.
Physical Fitment Evidence
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
Before fitting the left unit, inspect the lower valance and nearby exhaust trim for adequate operating clearance because facelift bumpers can retain the same vehicle name with different apertures.
While the HYUNDAI bumper opening is accessible, check the rear housing projection against the space behind the bumper skin so left- and right-hand stock cannot be mixed during consolidation.
Surface, Seal and Electrical Interface
Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.
During comparison of the HYUNDAI rear component, compare the bumper corner radius with the product face from more than one viewing angle so the approved product can be picked consistently in a mixed wholesale order.
For a repeat order of the left version, align each locating tab with the matching slot before applying hand pressure so hidden brackets are not loaded or bent during installation.
Bumper Assembly Check
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.
On the 2016 Santa Fe bumper layout, check whether the original component uses a separate retainer or an integral locking tab to preserve access for a final electrical test where a lamp circuit is present.
At the workshop selection stage for Santa Fe, verify the fastener direction and the shape of the concealed support frame to reduce clip damage during a no-force trial installation.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 92405-4Z500 |
| Cross-reference numbers | 92405-4Z500 |
| Internal item code | HY04004-027 |
| Vehicle brand | HYUNDAI |
| Vehicle model | Santa Fe |
| Model year | 2016 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
At the left rear-bumper position, protect the visible surface until the full perimeter gap has been accepted to prevent a visually similar version from sitting proud of the bumper.
When reviewing the 2016 vehicle, review the reflector texture and lens colour in neutral workshop light before the packaging and carton marking are finalized.
Frequently Asked Questions
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Is this component illuminated or reflector-only?
Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
Request a Product-Specific Quote
The sales team can check whether accessories shown in the photograph are part of the requested scope.
