92404-3S000 Rear Bumper Light for HYUNDAI Sonata 2011-2013 Right
Primary OE reference: 92404-3S000
Product type: Rear Bumper Light
Applicable vehicle: HYUNDAI Sonata 2011-2013
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: HYUNDAI
Model: Sonata
Vehicle year: 2011-2013
Physical comparison: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical check: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Installation guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
Wholesale enquiry: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
92404-3S000 Rear Bumper Light Overview
This product is listed for HYUNDAI Sonata 2011-2013 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
Before fitting the right unit, check the rear housing projection against the space behind the bumper skin because facelift bumpers can retain the same vehicle name with different apertures.
Application and Rear-Bumper Position
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
While the HYUNDAI bumper opening is accessible, compare the bumper corner radius with the product face from more than one viewing angle so left- and right-hand stock cannot be mixed during consolidation.
During comparison of the HYUNDAI rear component, align each locating tab with the matching slot before applying hand pressure so the approved product can be picked consistently in a mixed wholesale order.
Optical Face and Connector Review
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Protect the exposed face from tools and fasteners while the bumper liner is open for access.
For a repeat order of the right version, check whether the original component uses a separate retainer or an integral locking tab so hidden brackets are not loaded or bent during installation.
On the 2011-2013 Sonata bumper layout, verify the fastener direction and the shape of the concealed support frame to preserve access for a final electrical test where a lamp circuit is present.
Workshop Fitting Sequence
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.
At the workshop selection stage for Sonata, protect the visible surface until the full perimeter gap has been accepted to reduce clip damage during a no-force trial installation.
At the right rear-bumper position, review the reflector texture and lens colour in neutral workshop light to prevent a visually similar version from sitting proud of the bumper.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 92404-3S000 |
| Cross-reference numbers | 92404-3S000 |
| Internal item code | HY04004-016 |
| Vehicle brand | HYUNDAI |
| Vehicle model | Sonata |
| Model year | 2011-2013 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
The visible face should remain separated from tape, staples and loose hardware throughout transport.
When reviewing the 2011-2013 vehicle, record the approved side and vehicle application for repeat-order identification before the packaging and carton marking are finalized.
For the HYUNDAI Sonata application, confirm that the cable exit, where fitted, clears the bumper reinforcement before inner liners make the rear attachment points difficult to inspect.
Frequently Asked Questions
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Request a Product-Specific Quote
Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.
