92102-1C505 Head Light for HYUNDAI Getz 2006 Right
Primary OE reference: 92102-1C505
Cross-reference number 1: 92102-1C505
Product type: Head Light Assembly
Applicable vehicle: HYUNDAI Getz 2006
Installation position: Right front headlamp position
Brand: HYUNDAI
Model: Getz
Vehicle year: 2006
Lighting configuration: Match the photographed optical configuration
Housing comparison: Check the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate adjacent variants.
Optical system: Look over the lens pattern, internal bezel finish and optical modules so the requested unit matches the intended lighting package.
Electrical interface: The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.
Mounting points: Check mounting-ear spacing and support height against the removed lamp, including any hidden guide pin behind the bumper or grille edge.
Installation guidance: Complete a no-force trial fit first; once the panel gaps are even, secure the unit and adjust the beam to workshop specifications.
Wholesale packing: For repeat orders, keep the approved product photographs and application record so the same optical and mounting version is requested.
Application-specific focus: For the right HYUNDAI Getz application with match the photographed optical configuration, review reflector colour, projector presence and any decorative internal trim before approving a left/right pair for one vehicle.
Head Light Assembly Overview
This product record supports physical comparison of a front lamp assembly for workshop replacement and wholesale purchasing. It is catalogued under OE reference 92102-1C505 for HYUNDAI Getz 2006, with the right position identified in the source record.
The photographed lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Look over the lens pattern, internal bezel finish and optical modules so the chosen unit matches the intended lighting package.
For the Getz application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use alternative internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Review the complete lamp body from several angles because a similar lens can conceal a alternative rear casing or bracket offset.
Review mounting-ear spacing and support height against the removed lamp, including any hidden guide pin behind the bumper or grille edge.
Connector and Control Hardware
Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
Confirm the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
Use appropriate workshop procedures for removal and refitting, then verify that vibration, panel pressure and cable routing do not stress the housing.
A qualified workshop should look over surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | 92102-1C505 |
| Cross-reference numbers | 92102-1C505 |
| Internal item code | HY04001-022 |
| Vehicle brand | HYUNDAI |
| Vehicle model | Getz |
| Model year | 2006 |
| Installation position | Right front |
| Lighting configuration | Match the photographed optical configuration |
Wholesale Supply and Protective Packing
For wholesale supply, the lens should be isolated from carton pressure while the rear shell, adjusters and projecting mounting tabs are supported.
When requesting a quotation, state the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this right HYUNDAI Getz headlamp, the correspond to the photographed optical configuration specification should be assessed together with the 2006 body application. Review the rear housing depth, outer lens contour and the relationship between the grille-side and fender-side edges with the removed lamp.
The right Getz lighting package should remain the reference during electrical review. The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.
When fitting the HYUNDAI Getz unit at the right front position, preserve even body gaps and the intended beam orientation. Keep wiring clear of hot or moving components, then test low beam, high beam, indicator and daytime lighting where applicable.
Frequently Asked Questions
Can a headlamp be chosen by appearance alone?
No. The right lamp must also correspond to the optical system, electrical interface, mounting features and market specification.
How should the lamp be protected during shipping?
The lens needs isolation from carton pressure, while the rear housing and projecting tabs require stable internal support.
What distinguishes nearby lighting variants?
Reflector, projector, xenon and LED versions can differ in modules, daytime-light layout, internal bezel and plug configuration.
How can connector compatibility be reviewed?
Evaluate keying, terminal count, latch direction and wire exit, then identify any required ballast, driver or levelling motor.
What information supports a wholesale quotation?
State the HYUNDAI Getz application, production year, right side, lighting version, quantity and delivery country.
