92102-0X020 Head Light for HYUNDAI i10 2007 Right
Primary OE reference: 92102-0X020
Cross-reference number 1: 92102-0X020
Product type: Head Light Assembly
Applicable vehicle: HYUNDAI i10 2007
Installation position: Right front headlamp position
Brand: HYUNDAI
Model: i10
Vehicle year: 2007
Lighting configuration: power-adjustment version
Housing comparison: Inspect the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate surrounding variants.
Optical system: Inspect the lens pattern, internal bezel finish and optical modules so the requested unit matches the intended lighting package.
Electrical interface: Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
Mounting points: Support projecting tabs during handling and verify that each locating feature enters the correct body-side slot during the dry fit.
Installation guidance: Transfer only undamaged reusable hardware, establish the rear caps seal correctly and verify lamp operation before completing surrounding trim.
Wholesale packing: For repeat orders, record the approved product photographs and application record so the same optical and mounting version is requested.
Application-specific focus: For the right HYUNDAI i10 application with power-adjustment version, review the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.
Head Light Assembly Overview
This product record supports physical comparison of a front lamp assembly for workshop replacement and wholesale purchasing. It is catalogued under OE reference 92102-0X020 for HYUNDAI i10 2007, with the right position identified in the source record.
The external lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Examine the lens pattern, internal bezel finish and optical modules so the specified unit matches the intended lighting package.
For the i10 application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use distinct internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Validate that the headlamp sits naturally in the body opening and follows the bonnet, grille and fender lines without forced alignment.
Support projecting tabs during handling and verify that each locating feature enters the correct body-side slot during the dry fit.
Connector and Control Hardware
Do not use connector colour as the only selection point; terminal geometry, locking tabs and installed modules must also agree.
Validate the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
Use appropriate workshop procedures for removal and refitting, then establish that vibration, panel pressure and cable routing do not stress the housing.
A qualified workshop should examine surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | 92102-0X020 |
| Cross-reference numbers | 92102-0X020 |
| Internal item code | HY04001-296 |
| Vehicle brand | HYUNDAI |
| Vehicle model | i10 |
| Model year | 2007 |
| Installation position | Right front |
| Lighting configuration | power-adjustment version |
Wholesale Supply and Protective Packing
For wholesale supply, the lens should be isolated from carton pressure while the rear shell, adjusters and projecting mounting tabs are supported.
When requesting a quotation, state the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this right HYUNDAI i10 headlamp, the power-adjustment version specification should be assessed together with the 2007 body application. Verify the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate adjacent variants.
The right i10 lighting package should remain the reference during electrical review. Do not use connector colour as the only selection point; terminal geometry, locking tabs and installed modules must also agree.
When fitting the HYUNDAI i10 unit at the right front position, preserve even body gaps and the intended beam orientation. Transfer only undamaged reusable hardware, validate the rear caps seal correctly and verify lamp operation before completing surrounding trim.
Frequently Asked Questions
What photographs are useful for comparison?
Clear front, rear, connector and mounting-tab views help distinguish the required headlamp from a similar-looking alternative.
What information supports a wholesale quotation?
State the HYUNDAI i10 application, production year, right side, lighting version, quantity and delivery country.
Why must the rear housing be compared?
A similar lens can conceal a distinct casing depth, cap arrangement or bracket offset, preventing correct seating in the body opening.
How can connector compatibility be reviewed?
Compare keying, terminal count, latch direction and wire exit, then determine any required ballast, driver or levelling motor.
What distinguishes adjacent lighting variants?
Reflector, projector, xenon and LED versions can differ in modules, daytime-light layout, internal bezel and plug configuration.
