8W0955276 Front Right Headlight Washer Nozzle Cover for AUDI A4 2016

8W0955276 Front Right Headlight Washer Nozzle Cover Product Overview

The component shown under 8W0955276 is a front right headlight washer nozzle cover intended for AUDI A4 2016. The visible cover closes the bumper opening around the washer unit and follows the surrounding bumper contour when the nozzle is retracted. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A4

Compatibility for 8W0955276 should be confirmed against AUDI A4 2016 and the right installation side. The review should compare the hose connection or cover hinge with the original part, review painted, primed and unpainted finish requirements, and check whether the original cover is supplied separately from its support. Use the removed part and product photographs to compare the complete OE marking with the removed washer component, confirm the destination-market equipment specification, and verify that the OE reference is not for the opposite side; finally, confirm that the listed model designation matches the vehicle and use the full OE number, not a partial family reference.

Headlight Washer Nozzle Cover Function and Design Notes

The visible and hidden interfaces of AD02010-024 should be checked separately. For this headlight washer nozzle cover, check the joint between the visible cap and hidden support, review the clip geometry on the rear face, and compare the distance between mounting points. A direct comparison with the removed part should additionally inspect the hose connector for ovality, check the nozzle outlet orientation, and review the left-to-right mirrored geometry. Before the item is accepted, compare the retracted position with the bumper surface and inspect the base bracket around every locating slot.

OE Identification and Side Confirmation

8W0955276 is the primary OE identity for this right front right headlight washer nozzle cover, while AD02010-024 is the internal item code. Match both references to the vehicle record, then compare product photographs with the removed part from several angles. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-024 begins before the bumper area is disturbed: tighten bracket hardware only after alignment and complete a final visual check under even lighting. During trial fitting, tighten bracket hardware only after alignment, complete a final visual check under even lighting, and tighten bracket hardware only after alignment. Before returning the vehicle to service, complete a final visual check under even lighting, tighten bracket hardware only after alignment, and complete a final visual check under even lighting.

Receiving Inspection

When AD02010-024 arrives, receiving staff should inspect the visible cover face for scratches or pressure marks, review the hose spigot for impact damage or distortion, and check the spring-return area where the component includes an actuator. Before workshop release, record carton damage before the item is moved to workshop stock, compare connector depth and hose angle with the retained original part, photograph the received item if the vehicle fitment is still pending, and check the cap hinge or retaining point for free movement. Complete the inspection by ensuring that staff check the actuator body for straightness before trial installation, review the production finish against the approved sample, and check the carton partition for evidence of part-to-part contact.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8W0955276, please use dividers to prevent caps from rubbing each other, confirm whether caps and nozzles should be supplied as pairs, and include the full OE reference on the purchase order. Packing instructions should request a packing-list breakdown by internal item code, identify project stock and service stock separately, and identify the required installation side. Before dispatch, confirm sample approval before mass shipment and request barcode or private-label details when needed.

Frequently Asked Questions

Are clips, hoses or fasteners supplied with 8W0955276?

The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. For item AD02010-024, the approval should provide the complete destination address or port. The same item record should also verify the packed quantity by OE reference.

Can 8W0955276 fit every A4 model year?

No. Styling changes and market equipment can alter washer locations and mounting geometry. Use the listed year and full OE number as the starting point for confirmation. On the listed AUDI A4 2016, technicians should use the full OE number, not a partial family reference. A workshop comparison should additionally use the full OE number, not a partial family reference.

Is a sample order available for 8W0955276?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For the right-side order line, check carton labels at receiving. The order review should further use dividers to prevent caps from rubbing each other.

What should be inspected when 8W0955276 arrives?

Check the item label, side, contour, tabs, fluid connection, supplied components and carton condition before fitting or discarding the packaging. The product-specific check for 8W0955276 should check the carton partition for evidence of part-to-part contact. Receiving staff should also record carton damage before the item is moved to workshop stock.

What information should accompany a 8W0955276 enquiry?

Send the complete OE number, vehicle model and year, installation side, original-part photographs, quantity and delivery destination. Before this headlight washer nozzle cover is accepted, confirm whether the visible cover needs a primed or finished surface. Before approval, the buyer or technician should list model years and bumper versions for mixed orders.