8V0955101 Front Left Headlight Washer Nozzle for AUDI A3 2014

8V0955101 Front Left Headlight Washer Nozzle Product Overview

The component shown under 8V0955101 is a front left headlight washer nozzle intended for AUDI A3 2014. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A3

Compatibility for 8V0955101 should be confirmed against AUDI A3 2014 and the left installation side. The review should compare every tab, clip seat and locating shoulder, check the washer jet position relative to the headlamp lens, and match the exact model year and bumper revision. Use the removed part and product photographs to confirm the destination-market equipment specification, confirm whether a cap, nozzle, bracket or complete assembly is required, and check regional variations in headlamp-cleaning equipment; finally, compare every tab, clip seat and locating shoulder and check the washer jet position relative to the headlamp lens.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-013 should be checked separately. For this headlight washer nozzle, review the sealing area around the hose connection, check each molded locator against the original component, and inspect the molded tabs for cracks or distortion. A direct comparison with the removed part should additionally compare the cap-to-support engagement method, review the left-to-right mirrored geometry, and check the joint between the visible cap and hidden support. Before the item is accepted, inspect the telescopic body for smooth movement and compare the depth of the actuator body.

OE Identification and Side Confirmation

8V0955101 is the primary OE identity for this left front left headlight washer nozzle, while AD02010-013 is the internal item code. Match both references to the vehicle record, then confirm that the listed model designation matches the vehicle. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-013 begins before the bumper area is disturbed: route the washer hose away from sharp edges and inspect nearby wiring and sensors before refitting trim. During trial fitting, complete a final visual check under even lighting, clean the hose and connector before assembly, and use hand pressure rather than levering narrow plastic tabs. Before returning the vehicle to service, transfer reusable clips only after checking their condition, follow the vehicle workshop procedure for bumper removal, and inspect the bumper opening after the trial fit.

Receiving Inspection

When AD02010-013 arrives, receiving staff should measure the main mounting span when two bumper versions appear similar, confirm the internal item code before mixed stock is shelved, and check the carton partition for evidence of part-to-part contact. Before workshop release, document any shortage before the receiving inspection is closed, verify the nozzle head returns smoothly without applying excess force, inspect the fluid passage only with clean, non-damaging tools, and compare the supplied side with the vehicle repair order. Complete the inspection by ensuring that staff protect the visible face again after inspection is complete, match the item label to the purchase order and OE reference, and inspect the visible cover face for scratches or pressure marks.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8V0955101, please request barcode or private-label details when needed, provide the complete destination address or port, and provide the consignee and freight-forwarder details. Packing instructions should confirm whether the visible cover needs a primed or finished surface, separate fragile actuator bodies from heavier metal parts, and protect hose spigots and projecting tabs. Before dispatch, state any outer-carton marking requirements and state the target vehicle application.

Frequently Asked Questions

Which side uses 8V0955101?

This front left headlight washer nozzle is catalogued for the left side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. For item AD02010-013, the approval should compare the retracted position with the bumper surface. The same item record should also check each molded locator against the original component.

Which vehicle application is listed for 8V0955101?

8V0955101 is listed for AUDI A3 2014. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. On the listed AUDI A3 2014, technicians should review facelift and pre-facelift washer layouts. A workshop comparison should additionally retain the removed component for a direct physical comparison.

How should 8V0955101 be packed for export?

The front left headlight washer nozzle should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. For the left-side order line, verify the packed quantity by OE reference. The order review should further use dividers to prevent caps from rubbing each other.

How should 8V0955101 be checked before installation?

Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. The product-specific check for 8V0955101 should compare the washer opening beside the correct headlamp. Receiving staff should also use the full OE number, not a partial family reference.

What information should accompany a 8V0955101 enquiry?

Send the complete OE number, vehicle model and year, installation side, original-part photographs, quantity and delivery destination. Before this headlight washer nozzle is accepted, verify the packed quantity by OE reference. Before approval, the buyer or technician should separate left and right items on the packing list.