8P0955101B Front Left Headlight Washer Nozzle for AUDI A3 2010-2013

8P0955101B Front Left Headlight Washer Nozzle Product Overview

The component shown under 8P0955101B is a front left headlight washer nozzle intended for AUDI A3 2010-2013. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A3

Compatibility for 8P0955101B should be confirmed against AUDI A3 2010-2013 and the left installation side. The review should compare the washer opening beside the correct headlamp, inspect the bumper cutout shape and surrounding contour, and review body-style differences within the same model generation. Use the removed part and product photographs to verify the required left or right installation side, confirm whether a cap, nozzle, bracket or complete assembly is required, and confirm that the listed model designation matches the vehicle; finally, compare the complete OE marking with the removed washer component and compare the hose connection or cover hinge with the original part.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-015 should be checked separately. For this headlight washer nozzle, inspect the hose connector for ovality, compare the cap-to-support engagement method, and review the engagement of the cover with the nozzle stem. A direct comparison with the removed part should additionally check the cap hinge or retaining point, inspect the rear reinforcement ribs, and compare the retracted position with the bumper surface. Before the item is accepted, review the spring-loaded return features where fitted and check each molded locator against the original component.

OE Identification and Side Confirmation

8P0955101B is the primary OE identity for this left front left headlight washer nozzle, while AD02010-015 is the internal item code. Match both references to the vehicle record, then verify nearby parking-sensor or trim interfaces. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-015 begins before the bumper area is disturbed: paint or finish visible covers before final installation when required and align the cover flush with the bumper surface. During trial fitting, use hand pressure rather than levering narrow plastic tabs, test the spray direction before returning the vehicle, and photograph the original routing before disassembly. Before returning the vehicle to service, support the bumper cover while accessing the hidden actuator, complete a final visual check under even lighting, and keep dirt out of open washer-fluid lines.

Receiving Inspection

When AD02010-015 arrives, receiving staff should verify the cover contour against the approved product photograph, check painted or primed surfaces under neutral lighting, and photograph the received item if the vehicle fitment is still pending. Before workshop release, compare the visible surface texture with the ordered specification, measure the main mounting span when two bumper versions appear similar, inspect the fluid passage only with clean, non-damaging tools, and check molded tabs for whitening, cracks or transport stress. Complete the inspection by ensuring that staff check the spring-return area where the component includes an actuator, verify the supplied scope before discarding dividers or inner bags, and retain the OE label until the washer system has passed its function test.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8P0955101B, please request replacement-part documentation when required, confirm the acceptable delivery window, and identify painted and unpainted variants on separate lines. Packing instructions should protect each nozzle outlet from dust during transit, state the required order quantity, and provide the complete destination address or port. Before dispatch, send photographs of the removed washer part and include the full OE reference on the purchase order.

Frequently Asked Questions

How should 8P0955101B be checked before installation?

Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. For item AD02010-015, the approval should verify the required left or right installation side. The same item record should also confirm that the vehicle is equipped with a factory headlight washer system.

Is 8P0955101B a complete headlight washer system?

No. This listing covers the pictured headlight washer nozzle. The pump, reservoir, hoses, opposite-side parts and headlamp assembly are not included unless shown in the photographs. On the listed AUDI A3 2010-2013, technicians should use dividers to prevent caps from rubbing each other. A workshop comparison should additionally state the target vehicle application.

How should 8P0955101B be packed for export?

The front left headlight washer nozzle should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. For the left-side order line, protect hose spigots and projecting tabs. The order review should further use dividers to prevent caps from rubbing each other.

Is a sample order available for 8P0955101B?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. The product-specific check for 8P0955101B should confirm the preferred incoterm. Receiving staff should also state the requested delivery schedule.

Which side uses 8P0955101B?

This front left headlight washer nozzle is catalogued for the left side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. Before this headlight washer nozzle is accepted, compare the distance between mounting points. Before approval, the buyer or technician should check the joint between the visible cap and hidden support.