8P0805607 Front Left Headlight Mounting Bracket for AUDI A3 2010-2013

8P0805607 Front Left Headlight Mounting Bracket Product Overview

The component shown under 8P0805607 is a front left headlight mounting bracket intended for AUDI A3 2010-2013. Confirm the left orientation, lamp-side contour, mounting geometry against the original vehicle part.

Fitment and Application for A3

When comparing 8P0805607 with the removed component, confirm whether the vehicle uses a special appearance package, compare the installation direction, and review facelift and pre-facelift styling. For an application-specific order, confirm the exact model year before placing the order, check whether the original part is mirrored, and confirm the decorative finish or painted surface.

For the listed 2010-2013 application, match the body style and equipment grade, review facelift and pre-facelift styling, and match the locator-slot arrangement. During receiving inspection, compare the stamped or moulded reference, confirm the exact model year before placing the order, and confirm the front installation position.

Before the original trim or bracket is discarded, confirm the front installation position, confirm whether the vehicle uses a special appearance package, and review the orientation of the moulded bracket. When organizing mixed-OE inventory, confirm the exact model year before placing the order, confirm the destination-market version, and compare every locating point and screw opening.

Headlight Mounting Bracket Design and Replacement Notes

Before confirming this headlight accessory, check mirrored geometry against the required side, compare the profile below the lamp lens, and compare gloss level with the neighbouring trim. For a repeat wholesale purchase, inspect the moulded front face and rear ribs, check the curvature beside the headlamp, and review fastening slots and clip seats.

For a body-shop order covering AUDI, compare gloss level with the neighbouring trim, review narrow tips for transport damage, and inspect moulded corners before installation. During the physical comparison, inspect both end geometries, inspect the overall frame width, and inspect the moulded front face and rear ribs.

When comparing 8P0805607 with the removed component, check the curvature beside the headlamp, review the thickness around each mounting boss, and inspect the back-side support structure. When checking the headlamp opening, compare the centre alignment point, compare the profile below the lamp lens, and check the interface with the lamp housing.

Application-Specific Identification

At receiving inspection with 8P0805607 on the A3 2010-2013: review facelift and pre-facelift styling. The AD02009-001 sample for the left side should compare reusable clips and hardware. Before installation, ensure that all removed hardware is accounted for; for a quotation, confirm replacement-part documentation needs.

For application-specific sourcing with 8P0805607 on the A3 2010-2013: compare every locating point and screw opening. The AD02009-001 sample for the left side should review nearby cover openings. Before installation, check the finish for tool marks before delivery; for a quotation, protect projecting locator tabs.

At receiving inspection with 8P0805607 on the A3 2010-2013: confirm the front installation position. The AD02009-001 sample for the left side should check the depth of the moulded locator channels. Before installation, protect painted and chrome surfaces; for a quotation, confirm the preferred incoterm.

Installation Guidance

When reviewing the visible finish on AD02009-001, confirm an evenly seated fit, route nearby wiring away from sharp edges, and photograph the completed installation for order records. For a no-force trial fit, check the adjoining panel gaps, check the final perimeter around the lamp, and replace distorted clips before final assembly.

Before sourcing this front left headlight mounting bracket, complete a visual check under even lighting, inspect broken vehicle-side mounts, and compare the installed height with the opposite side. While checking adjacent body parts, transfer reusable clips carefully, replace distorted clips before final assembly, and check the adjoining panel gaps.

Before confirming this headlight accessory, confirm that the hood and fender clearances remain even, verify that no fastener is cross-threaded, and photograph the completed installation for order records. Before the quotation is confirmed, support adjacent body panels evenly, align the headlamp edge before fastening, and check the adjoining panel gaps.

Product Technical Specifications

Wholesale Supply and Packing

For replacement in the left front headlamp area, request a packing-list breakdown by item code, confirm whether clips are required separately, and confirm the preferred incoterm. When organizing mixed-OE inventory, protect projecting locator tabs, identify mixed-OE orders clearly, and confirm replacement-part documentation needs.

When separating nearby A3 variants, send photographs of the removed component, include the complete OE reference, and confirm the required finish. While reviewing the supplied photographs, request supported export-carton packing, protect projecting locator tabs, and support long trim sections during transit.

When reviewing the visible finish on AD02009-001, inspect the carton at receiving, request the applicable export terms, and confirm barcode or private-label requirements. Before final installation, separate painted and unpainted variants, include the complete OE reference, and review edge protection inside the carton.

Frequently Asked Questions

How should 8P0805607 be checked before installation?

Compare the OE number, overall outline, locating tabs, screw points, surface finish and lamp-side contour with the removed part before hardware is tightened. For A3, confirm the exact model year before placing the order; measure the removed part where references are unclear; transfer reusable clips carefully; and request a packing-list breakdown by item code before fitting or quotation.

Does the finish specification matter for 8P0805607?

Yes. Different vehicle grades can change colour, coating, visible texture and locating details, so compare the original part carefully. For A3, compare the complete OE marking with the removed part; review the thickness around each mounting boss; support adjacent body panels evenly; and confirm the requested delivery schedule before fitting or quotation.

Does 8P0805607 include a complete headlamp assembly?

No. This page covers the pictured front left headlight mounting bracket. Lamps, bulbs, wiring, modules and separate fasteners are not included unless visibly shown in the product photographs. For A3, verify that the grille design matches the stated application; compare the centre alignment point; check the finish for tool marks before delivery; and include the complete OE reference before fitting or quotation.

Are clips and screws supplied with 8P0805607?

The supply scope follows the photographs. Reusable clips, screws, retainers or separate brackets should be confirmed before the order is finalized. For A3, check the lamp manufacturer where multiple units were fitted; check the interface with the lamp housing; reinstall removed seals in their original positions; and provide the consignee contact information before fitting or quotation.

Which side uses 8P0805607?

This front left headlight mounting bracket is catalogued for the left front headlamp area. Opposite-side parts normally use mirrored geometry and a different reference. For A3, match the accessory to the original bumper revision; inspect the junction with the fender edge; complete a visual check under even lighting; and confirm sample-order requirements before fitting or quotation.

Request a Quote

Send the complete OE reference 8P0805607, vehicle details, installation side, required quantity and delivery destination. Yongshang Auto can review the application before preparing a product-specific export quotation.