81920-0K050 Rear Bumper Light for TOYOTA Innova 2018 Left
Primary OE reference: 81920-0K050
Product type: Rear Bumper Light
Applicable vehicle: TOYOTA Innova 2018
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: TOYOTA
Model: Innova
Vehicle year: 2018
Physical comparison: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical check: Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Installation guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Production date and regional bumper specification should be reviewed when several near-identical versions are available.
Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.
Wholesale enquiry: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.
Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
81920-0K050 Rear Bumper Light Overview
This product is listed for TOYOTA Innova 2018 at the left rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.
At the workshop selection stage for Innova, use the opposite-side component only as an alignment reference, not as an interchange part to reduce clip damage during a no-force trial installation.
Vehicle Fitment and Bumper Interface
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Use the removed component as the physical reference for outer shape, housing projection and clip location.
At the left rear-bumper position, compare the outer lens edge with the moulded bumper recess to prevent a visually similar version from sitting proud of the bumper.
When reviewing the 2018 vehicle, inspect the lower valance and nearby exhaust trim for adequate operating clearance before the packaging and carton marking are finalized.
Reflector, Lens and Electrical Configuration
Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.
For the TOYOTA Innova application, check the rear housing projection against the space behind the bumper skin before inner liners make the rear attachment points difficult to inspect.
For this Innova body configuration, compare the bumper corner radius with the product face from more than one viewing angle so the visible gap remains even after every retaining point is engaged.
Installation and Functional Check
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.
Before approving the Innova part for packing, align each locating tab with the matching slot before applying hand pressure so the lens and housing are supported without distortion.
Before fitting the left unit, check whether the original component uses a separate retainer or an integral locking tab so a passive reflector is not confused with an illuminated assembly.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 81920-0K050 |
| Cross-reference numbers | 81920-0K050 |
| Internal item code | TY04004-045 |
| Vehicle brand | TOYOTA |
| Vehicle model | Innova |
| Model year | 2018 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
The visible face should remain separated from tape, staples and loose hardware throughout transport.
While the TOYOTA bumper opening is accessible, verify the fastener direction and the shape of the concealed support frame to verify that the photographed configuration matches the vehicle in the workshop.
During comparison of the TOYOTA rear component, protect the visible surface until the full perimeter gap has been accepted to avoid contact with wiring, body edges or hot exhaust components.
Frequently Asked Questions
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Request a Product-Specific Quote
Repeat buyers can reference the vehicle application and side from their previous approved sample.
