81910-02200 Rear Bumper Light for TOYOTA Corolla 2020 Right
Primary OE reference: 81910-02200
Product type: Rear Bumper Light
Applicable vehicle: TOYOTA Corolla 2020
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: TOYOTA
Model: Corolla
Vehicle year: 2020
Housing match: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Reflector or lamp role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Wiring confirmation: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Mounting sequence: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.
Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
Purchase information: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
81910-02200 Rear Bumper Light Overview
This product is listed for TOYOTA Corolla 2020 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
At the right rear-bumper position, inspect the lower valance and nearby exhaust trim for adequate operating clearance to prevent a visually similar version from sitting proud of the bumper.
Physical Fitment Evidence
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
When reviewing the 2020 vehicle, check the rear housing projection against the space behind the bumper skin before the packaging and carton marking are finalized.
For the TOYOTA Corolla application, compare the bumper corner radius with the product face from more than one viewing angle before inner liners make the rear attachment points difficult to inspect.
Surface, Seal and Electrical Interface
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
For this Corolla body configuration, align each locating tab with the matching slot before applying hand pressure so the visible gap remains even after every retaining point is engaged.
Before approving the Corolla part for packing, check whether the original component uses a separate retainer or an integral locking tab so the lens and housing are supported without distortion.
Bumper Assembly Check
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.
Before fitting the right unit, verify the fastener direction and the shape of the concealed support frame so a passive reflector is not confused with an illuminated assembly.
While the TOYOTA bumper opening is accessible, protect the visible surface until the full perimeter gap has been accepted to verify that the photographed configuration matches the vehicle in the workshop.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 81910-02200 |
| Cross-reference numbers | 81910-02200 |
| Internal item code | TY04004-029 |
| Vehicle brand | TOYOTA |
| Vehicle model | Corolla |
| Model year | 2020 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
During comparison of the TOYOTA rear component, review the reflector texture and lens colour in neutral workshop light to avoid contact with wiring, body edges or hot exhaust components.
For a repeat order of the right version, record the approved side and vehicle application for repeat-order identification to keep the optical face level with the surrounding painted surface.
Frequently Asked Questions
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Request a Product-Specific Quote
The quotation can include export packing requirements once the required variant and order volume are known.
