76881-SWA-S01 Front Left Headlight Washer Nozzle Cover for HONDA CR-V 2012
Primary OE reference: 76881-SWA-S01
Cross-reference number 1: 76881-SWA-S01
Cross-reference number 2: 76881SWAS01
Product type: Front Left Headlight Washer Nozzle Cover
Vehicle application: HONDA CR-V 2012
Installation position: Front bumper / headlight washer area
Side: Left
Brand: HONDA
Model: CR-V
Model year: 2012
Product function: Closes the bumper washer opening and restores the visible exterior contour around the headlamp.
Fitment check: Confirm the complete OE number, model year, bumper specification and left/right position before ordering.
Supply scope: The supplied components follow the product photographs; clips, hoses, seals and fasteners are included only when shown or separately confirmed.
Surface finish: Compare the visible colour and texture with the original part; painting may be required before final installation.
Internal item code: HD02010-021
Quotation information: Send the OE number, vehicle model/year, required side, quantity and delivery destination for an application-specific quotation.
76881-SWA-S01 Front Left Headlight Washer Nozzle Cover Product Overview
The component shown under 76881-SWA-S01 is a front left headlight washer nozzle cover intended for HONDA CR-V 2012. The visible cover closes the bumper opening around the washer unit and follows the surrounding bumper contour when the nozzle is retracted. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.
Fitment and Washer-System Application for CR-V
Compatibility for 76881-SWA-S01 should be confirmed against HONDA CR-V 2012 and the left installation side. The review should compare the nozzle travel direction with the vehicle-side installation, verify nearby parking-sensor or trim interfaces, and match the connector and fluid inlet position where applicable. Use the removed part and product photographs to confirm that the listed model designation matches the vehicle, compare every tab, clip seat and locating shoulder, and check whether the original cover is supplied separately from its support; finally, review body-style differences within the same model generation and compare product photographs with the removed part from several angles.
Headlight Washer Nozzle Cover Function and Design Notes
The visible and hidden interfaces of HD02010-021 should be checked separately. For this headlight washer nozzle cover, inspect the washer outlet for blockage, compare the cap perimeter and corner radii, and review any paint-preparation requirement before fitting. A direct comparison with the removed part should additionally check the cap hinge or retaining point, inspect the base bracket around every locating slot, and compare the depth of the actuator body. Before the item is accepted, review the left-to-right mirrored geometry and check each molded locator against the original component.
OE Identification and Side Confirmation
76881-SWA-S01 is the primary OE identity for this left front left headlight washer nozzle cover, while HD02010-021 is the internal item code. Match both references to the vehicle record, then compare the actuator orientation behind the bumper cover. Do not substitute the mirrored side merely because the visible cover shape appears similar.
Installation and System Testing Guidance
Workshop preparation for HD02010-021 begins before the bumper area is disturbed: compare the installed height with the opposite side and retain the original fasteners unless replacements are specified. During trial fitting, route the washer hose away from sharp edges, tighten bracket hardware only after alignment, and use hand pressure rather than levering narrow plastic tabs. Before returning the vehicle to service, reconfirm the OE number before discarding the packaging, check the system for leaks after reconnection, and keep dirt out of open washer-fluid lines.
Receiving Inspection
When HD02010-021 arrives, receiving staff should inspect the rear locator shape without forcing any movable section, confirm the internal item code before mixed stock is shelved, and verify the supplied scope before discarding dividers or inner bags. Before workshop release, inspect the fluid passage only with clean, non-damaging tools, photograph the received item if the vehicle fitment is still pending, inspect the visible cover face for scratches or pressure marks, and verify that protective plugs remain in open fluid connections. Complete the inspection by ensuring that staff compare left and right orientation before removing protective wrapping, inspect projecting pins before placing the item on a hard bench, and confirm that loose accessories are identified on the packing list.
Product Technical Specifications
| Product type | Front Left Headlight Washer Nozzle Cover |
|---|---|
| Primary OE reference | 76881-SWA-S01 |
| Cross-reference numbers | 76881-SWA-S01 76881SWAS01 |
| Internal item code | HD02010-021 |
| Vehicle brand | HONDA |
| Vehicle model | CR-V |
| Model year | 2012 |
| Installation position | Front bumper / headlamp washer area |
| Side / orientation | Left |
| Applicable vehicle | HONDA CR-V 2012 |
Wholesale Supply and Protective Packing
For a quotation or repeat order of 76881-SWA-S01, please identify painted and unpainted variants on separate lines, list model years and bumper versions for mixed orders, and separate fragile actuator bodies from heavier metal parts. Packing instructions should include the full OE reference on the purchase order, request barcode or private-label details when needed, and verify the packed quantity by OE reference. Before dispatch, plug open fluid connections during packing and request moisture protection for sea freight.
Frequently Asked Questions
Can product photographs alone confirm 76881-SWA-S01 compatibility?
Photographs are useful for visual comparison, but the full OE number, vehicle year, bumper version, side and washer equipment must also match. For item HD02010-021, the approval should compare the actuator orientation behind the bumper cover. The same item record should also confirm the destination-market equipment specification.
Are clips, hoses or fasteners supplied with 76881-SWA-S01?
The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. On the listed HONDA CR-V 2012, technicians should plug open fluid connections during packing. A workshop comparison should additionally identify the required installation side.
Is workshop installation recommended for 76881-SWA-S01?
Yes. A qualified workshop can access the bumper area on the CR-V, transfer hoses or clips safely and test the washer system for correct operation and leaks. For the left-side order line, reconnect every hose clip before filling the system. The order review should further verify that the cover closes without rubbing the bumper.
How should 76881-SWA-S01 be checked before installation?
Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. The product-specific check for 76881-SWA-S01 should match the exact model year and bumper revision. Receiving staff should also use the full OE number, not a partial family reference.
Which vehicle application is listed for 76881-SWA-S01?
76881-SWA-S01 is listed for HONDA CR-V 2012. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. Before this headlight washer nozzle cover is accepted, compare the hose connection or cover hinge with the original part. Before approval, the buyer or technician should inspect the bumper cutout shape and surrounding contour.
