71240-TZA-000 Front Right Headlight Mounting Bracket for HONDA Fit 2021

71240-TZA-000 Front Right Headlight Mounting Bracket Product Overview

The component shown under 71240-TZA-000 is a front right headlight mounting bracket intended for HONDA Fit 2021. Confirm the right orientation, lamp-side contour, mounting geometry against the original vehicle part.

Fitment and Application for Fit

When preparing a Fit body repair, check the vehicle production date where available, compare the headlight outline at both ends, and compare the complete OE marking with the removed part. Before final installation, review facelift and pre-facelift styling, confirm the destination-market version, and check the lamp manufacturer where multiple units were fitted.

During comparison with the original lamp surround, compare the installation direction, check the relationship with the lamp housing, and match the accessory to the original bumper revision. At the workshop preparation stage, match the locator-slot arrangement, compare every locating point and screw opening, and confirm whether the vehicle uses a special appearance package.

Before confirming export packing for 71240-TZA-000, compare the stamped or moulded reference, match the accessory to the original bumper revision, and compare the complete OE marking with the removed part. For a repeat wholesale purchase, review regional specification differences, compare every locating point and screw opening, and review facelift and pre-facelift styling.

Headlight Mounting Bracket Design and Replacement Notes

Before the original trim or bracket is discarded, inspect both end geometries, check mirrored geometry against the required side, and compare the visible texture and finish. Before clips or hardware are transferred, compare the profile below the lamp lens, check the adjoining panel gap, and compare gloss level with the neighbouring trim.

For HONDA Fit 2021, check the adjoining panel gap, compare reusable clips and hardware, and measure the removed part where references are unclear. At the alignment stage, inspect the back-side support structure, check the interface with the lamp housing, and review nearby cover openings.

When preparing a Fit body repair, compare mounting-hole height, inspect the junction with the fender edge, and compare the centre alignment point. For a no-force trial fit, measure the removed part where references are unclear, check mirrored geometry against the required side, and inspect the moulded front face and rear ribs.

Application-Specific Identification

At receiving inspection with 71240-TZA-000 on the Fit 2021: check whether the original part is mirrored. The HD02009-057 sample for the right side should compare the original edge profile. Before installation, inspect the surrounding guides; for a quotation, confirm the requested delivery schedule.

For application-specific sourcing with 71240-TZA-000 on the Fit 2021: compare the installation direction. The HD02009-057 sample for the right side should check the transition to the bumper or grille. Before installation, use hand pressure only during the initial engagement; for a quotation, inspect the carton at receiving.

At receiving inspection with 71240-TZA-000 on the Fit 2021: compare the installation direction. The HD02009-057 sample for the right side should confirm decorative surface details. Before installation, confirm the correct fitting direction; for a quotation, confirm whether clips are required separately.

Installation Guidance

When comparing 71240-TZA-000 with the removed component, align the headlamp edge before fastening, replace distorted clips before final assembly, and avoid bending narrow moulded tabs. For an application-specific order, use hand pressure only during the initial engagement, protect exposed edges during removal, and photograph the completed installation for order records.

For the listed 2021 application, keep the removed part nearby for comparison, confirm an evenly seated fit, and compare the installed height with the opposite side. During receiving inspection, inspect the lamp aim after surrounding parts are refitted, support adjacent body panels evenly, and confirm that every locator engages.

Before the original trim or bracket is discarded, check the final perimeter around the lamp, check the finish for tool marks before delivery, and confirm the correct fitting direction. When organizing mixed-OE inventory, use hand pressure only during the initial engagement, keep the removed part nearby for comparison, and check that no locator is trapped behind the bumper.

Product Technical Specifications

Wholesale Supply and Packing

Before confirming this headlight accessory, provide the consignee contact information, confirm the preferred incoterm, and confirm pallet requirements for larger quantities. For a repeat wholesale purchase, confirm the nominated freight forwarder, agree the acceptable delivery window, and provide the destination country.

For a body-shop order covering HONDA, confirm pallet requirements for larger quantities, request supported export-carton packing, and confirm the packing method. During the physical comparison, list every OE reference on the purchase order, include the complete OE reference, and state estimated annual purchasing volume.

When comparing 71240-TZA-000 with the removed component, agree the acceptable delivery window, state the destination port or city, and confirm replacement-part documentation needs. When checking the headlamp opening, confirm the requested delivery schedule, state the required order quantity, and request protective inner wrapping.

Frequently Asked Questions

How should 71240-TZA-000 be checked before installation?

Compare the OE number, overall outline, locating tabs, screw points, surface finish and lamp-side contour with the removed part before hardware is tightened. For Fit, check the lamp manufacturer where multiple units were fitted; check mirrored geometry against the required side; support adjacent body panels evenly; and request a packing-list breakdown by item code before fitting or quotation.

Does the finish specification matter for 71240-TZA-000?

Yes. Different vehicle grades can change colour, coating, visible texture and locating details, so compare the original part carefully. For Fit, match the locator-slot arrangement; inspect the moulded front face and rear ribs; check the adjoining panel gaps; and confirm the requested delivery schedule before fitting or quotation.

Does 71240-TZA-000 include a complete headlamp assembly?

No. This page covers the pictured front right headlight mounting bracket. Lamps, bulbs, wiring, modules and separate fasteners are not included unless visibly shown in the product photographs. For Fit, retain the original component for a direct comparison; inspect reinforcement features behind the part; confirm the correct fitting direction; and include the complete OE reference before fitting or quotation.

Are clips and screws supplied with 71240-TZA-000?

The supply scope follows the photographs. Reusable clips, screws, retainers or separate brackets should be confirmed before the order is finalized. For Fit, compare the stamped or moulded reference; inspect the overall frame width; inspect the surrounding guides; and provide the consignee contact information before fitting or quotation.

Which side uses 71240-TZA-000?

This front right headlight mounting bracket is catalogued for the right front headlamp area. Opposite-side parts normally use mirrored geometry and a different reference. For Fit, compare adjacent bumper and grille sections; check the depth of the moulded locator channels; replace distorted clips before final assembly; and confirm sample-order requirements before fitting or quotation.

Request a Quote

Send the complete OE reference 71240-TZA-000, vehicle details, installation side, required quantity and delivery destination. Yongshang Auto can review the application before preparing a product-specific export quotation.