71103-T6L-H02 Front Right Fog Light Bezel for HONDA Spirior 2015

71103-T6L-H02 Front Right Fog Light Bezel Product Overview

The product shown under 71103-T6L-H02 is a front right fog light bezel intended for HONDA Spirior 2015. Check the right orientation, lamp opening, mounting tabs and high-specification specification against the original component.

Fitment and Application for Spirior

Before sourcing this front right fog light bezel, compare every fixing tab, check the nearby lamp opening, and confirm the bumper position. At the workshop preparation stage, review facelift styling, match the outer contour, and check the vehicle build date.

Before confirming this fog light bezel, compare the original grille section, confirm the model year, and match the outer contour. For a repeat wholesale order, inspect the lamp aperture size, confirm the bumper position, and compare the installation direction.

For HONDA Spirior 2015, confirm the vehicle market, compare the installation direction, and match the locating-slot layout. While reviewing the supplied photographs, check adjacent bumper parts, confirm the surface finish, and review the bezel orientation.

Front Right Fog Light Bezel Design and Replacement Notes

When separating nearby Spirior variants, inspect the moulded face, check the bumper transition, and inspect the back-side structure. During the physical comparison, compare vent or grille openings, review fastening slots, and measure the original length.

When comparing 71103-T6L-H02 with the removed bezel, review fastening slots, compare the original edge profile, and inspect the frame width. When checking the bumper opening, measure the original length, compare the surface texture, and check the bezel curvature.

For the listed 2015 application, compare transferred hardware, measure the original length, and inspect the back-side structure. At the workshop preparation stage, check the lamp interface, review nearby cover openings, and compare mounting-hole height.

Application-Specific Identification Notes

Before workshop installation with 71103-T6L-H02 on the Spirior 2015: review market-version differences. The HD02008-048 sample for the right side should compare the original edge profile. For HONDA identification, 71103-T6L-H02 also requires technicians to verify the lamp remains centred. A buyer quoting HD02008-048 should state the destination port for the HONDA Spirior 2015 order.

For application-specific sourcing with 71103-T6L-H02 on the Spirior 2015: match the locating-slot layout. The HD02008-048 sample for the right side should inspect the moulded face. For HONDA identification, 71103-T6L-H02 also requires technicians to clean the bumper mounting area. A buyer quoting HD02008-048 should send photographs of the removed part for the HONDA Spirior 2015 order.

Before workshop installation with 71103-T6L-H02 on the Spirior 2015: review market-version differences. The HD02008-048 sample for the right side should check the lamp interface. For HONDA identification, 71103-T6L-H02 also requires technicians to trial-fit the bezel without force. A buyer quoting HD02008-048 should request protective inner wrapping for the HONDA Spirior 2015 order.

For application-specific sourcing with 71103-T6L-H02 on the Spirior 2015: verify the mounting side. The HD02008-048 sample for the right side should review locator direction. For HONDA identification, 71103-T6L-H02 also requires technicians to confirm every locator engages. A buyer quoting HD02008-048 should confirm sample requirements for the HONDA Spirior 2015 order.

Installation Guidance

Before sourcing this front right fog light bezel, retain the removed bezel for comparison, support the bumper cover evenly, and protect exposed panel edges. While checking adjacent body parts, inspect damaged mounting points, review the completed alignment, and avoid bending moulded tabs.

Before confirming this fog light bezel, check the final perimeter, review separate hardware needs, and protect exposed panel edges. Before clips or hardware are transferred, confirm the fitting direction, inspect each screw point, and check lamp-to-bezel clearance.

For HONDA Spirior 2015, clean the bumper mounting area, check adjacent panel gaps, and protect exposed panel edges. During the physical comparison, verify the lamp remains centred, transfer reusable clips carefully, and confirm the fitting direction.

Product Technical Specifications

Wholesale Supply and Packing

When separating nearby Spirior variants, confirm the delivery schedule, request export quotation terms, and compare the supplied photographs. Before packing the confirmed item, state the target vehicle, inspect receiving condition, and request supported carton packing.

When comparing 71103-T6L-H02 with the removed bezel, confirm the required finish, support the bezel during transit, and confirm sample requirements. For a no-force trial fit, confirm separate clip requirements, state annual purchasing volume, and state the destination port.

For the listed 2015 application, confirm sample requirements, provide the delivery country, and compare the supplied photographs. While checking adjacent body parts, request supported carton packing, confirm the packing method, and retain the product label.

Frequently Asked Questions

Why must the left and right versions of 71103-T6L-H02 be distinguished?

Left and right bezels are normally mirror-specific. Their curves, screw points and locator tabs should not be assumed interchangeable. For Spirior, review market-version differences, check the adjoining gap, avoid bending moulded tabs, and support the bezel during transit before installation or quotation.

Is workshop installation recommended for 71103-T6L-H02?

Yes. A workshop can inspect damaged bumper mounts on the Spirior, align the lamp opening and avoid forcing a bezel intended for another trim level. For Spirior, review market-version differences, compare vent or grille openings, inspect the surrounding guides, and request export quotation terms before installation or quotation.

Are mounting clips supplied with 71103-T6L-H02?

The supply scope follows the product photographs. Reusable clips, screws or separate brackets should be confirmed before the order is finalized. For Spirior, review market-version differences, inspect reinforcement ribs, check adjacent panel gaps, and request supported carton packing before installation or quotation.

Does 71103-T6L-H02 include the complete lamp assembly?

No. This listing covers the pictured front right fog light bezel. The fog lamp, bulbs, wiring, switches and separate clips are not included unless they are visibly shown. For Spirior, review market-version differences, review the outer-edge shape, confirm an evenly seated fit, and check the ordered mounting side before installation or quotation.

How should 71103-T6L-H02 be protected for export?

The bezel should be supported inside the carton with its narrow edges, lamp opening and projecting tabs protected against compression, abrasion and impact. For Spirior, review market-version differences, check the bumper transition, inspect damaged mounting points, and include the complete OE reference before installation or quotation.

Request a Quote

Send the complete OE reference 71103-T6L-H02, vehicle details, mounting side, quantity and destination. Yongshang Auto can review the application before preparing a product-specific export quotation.