71102-TBT-H70 Front Right Fog Light Bezel for HONDA Crider 2022

71102-TBT-H70 Front Right Fog Light Bezel Product Overview

The product shown under 71102-TBT-H70 is a front right fog light bezel intended for HONDA Crider 2022. Check the right orientation, lamp opening, mounting tabs and standard-specification specification against the original component.

Fitment and Application for Crider

During an OE-led review for HD02008-128, compare the full OE marking, inspect the lamp aperture size, and confirm the vehicle market. Before packing the confirmed item, compare the installation direction, match the locating-slot layout, and check adjacent bumper parts.

For wholesale selection of 71102-TBT-H70, compare every fixing tab, review facelift styling, and compare the original grille section. For a no-force trial fit, check adjacent bumper parts, confirm the vehicle market, and confirm the model year.

Before sourcing this front right fog light bezel, compare the original grille section, inspect the removed bezel, and confirm the vehicle market. While checking adjacent body parts, check the vehicle build date, verify the mounting side, and compare the installation direction.

Front Right Fog Light Bezel Design and Replacement Notes

During comparison with the original lamp surround, review nearby cover openings, compare mounting-hole height, and inspect the frame width. During receiving inspection, review the outer-edge shape, confirm decorative finish details, and compare vent or grille openings.

For replacement in the right front area, inspect the moulded face, inspect reinforcement ribs, and inspect the frame width. Before the quotation is confirmed, inspect the end geometry, inspect the back-side structure, and compare the original edge profile.

When separating nearby Crider variants, review fastening slots, check the bezel curvature, and inspect the moulded face. Before packing the confirmed item, review the outer-edge shape, review nearby cover openings, and measure the original length.

Application-Specific Identification Notes

A vehicle-side comparison starts with 71102-TBT-H70 on the Crider 2022: check the vehicle build date. The HD02008-128 sample for the right side should measure the original length. For HONDA identification, 71102-TBT-H70 also requires technicians to avoid bending moulded tabs. A buyer quoting HD02008-128 should request supported carton packing for the HONDA Crider 2022 order.

For application-specific sourcing with 71102-TBT-H70 on the Crider 2022: match the outer contour. The HD02008-128 sample for the right side should inspect the moulded face. For HONDA identification, 71102-TBT-H70 also requires technicians to confirm the finished bumper gap. A buyer quoting HD02008-128 should confirm the delivery schedule for the HONDA Crider 2022 order.

A trim-level comparison requires with 71102-TBT-H70 on the Crider 2022: review market-version differences. The HD02008-128 sample for the right side should check the bezel curvature. For HONDA identification, 71102-TBT-H70 also requires technicians to check lamp-to-bezel clearance. A buyer quoting HD02008-128 should request supported carton packing for the HONDA Crider 2022 order.

Before workshop installation with 71102-TBT-H70 on the Crider 2022: match the outer contour. The HD02008-128 sample for the right side should inspect the moulded face. For HONDA identification, 71102-TBT-H70 also requires technicians to align the lamp opening first. A buyer quoting HD02008-128 should confirm the required finish for the HONDA Crider 2022 order.

Installation Guidance

During an OE-led review for HD02008-128, align the lamp opening first, check lamp-to-bezel clearance, and review the completed alignment. While reviewing the supplied photographs, trial-fit the bezel without force, retain the removed bezel for comparison, and confirm an evenly seated fit.

For wholesale selection of 71102-TBT-H70, retain the removed bezel for comparison, inspect damaged mounting points, and clean the bumper mounting area. Before final installation, confirm an evenly seated fit, inspect each screw point, and check adjacent panel gaps.

Before sourcing this front right fog light bezel, check the final perimeter, confirm an evenly seated fit, and review the completed alignment. During receiving inspection, inspect the surrounding guides, confirm the finished bumper gap, and verify the lamp remains centred.

Product Technical Specifications

Wholesale Supply and Packing

During comparison with the original lamp surround, compare the supplied photographs, request supported carton packing, and confirm the packing method. At the workshop preparation stage, retain the product label, state the required quantity, and confirm separate clip requirements.

For replacement in the right front area, confirm the delivery schedule, state the destination port, and confirm the packing method. For a repeat wholesale order, request export quotation terms, state annual purchasing volume, and check the ordered mounting side.

When separating nearby Crider variants, confirm the required finish, state the target vehicle, and confirm the packing method. While reviewing the supplied photographs, include the complete OE reference, confirm sample requirements, and request export quotation terms.

Frequently Asked Questions

Why must the left and right versions of 71102-TBT-H70 be distinguished?

Left and right bezels are normally mirror-specific. Their curves, screw points and locator tabs should not be assumed interchangeable. For Crider, compare the installation direction, check the adjoining gap, check adjacent panel gaps, and include the complete OE reference before installation or quotation.

Is workshop installation recommended for 71102-TBT-H70?

Yes. A workshop can inspect damaged bumper mounts on the Crider, align the lamp opening and avoid forcing a bezel intended for another trim level. For Crider, review market-version differences, inspect reinforcement ribs, inspect damaged mounting points, and provide the delivery country before installation or quotation.

Are mounting clips supplied with 71102-TBT-H70?

The supply scope follows the product photographs. Reusable clips, screws or separate brackets should be confirmed before the order is finalized. For Crider, review facelift styling, check the bumper transition, trial-fit the bezel without force, and request protective inner wrapping before installation or quotation.

Does 71102-TBT-H70 include the complete lamp assembly?

No. This listing covers the pictured front right fog light bezel. The fog lamp, bulbs, wiring, switches and separate clips are not included unless they are visibly shown. For Crider, check adjacent bumper parts, inspect the end geometry, support the bumper cover evenly, and state the destination port before installation or quotation.

How should 71102-TBT-H70 be protected for export?

The bezel should be supported inside the carton with its narrow edges, lamp opening and projecting tabs protected against compression, abrasion and impact. For Crider, confirm the model year, check the bezel curvature, verify the lamp remains centred, and request export quotation terms before installation or quotation.

Request a Quote

Send the complete OE reference 71102-TBT-H70, vehicle details, mounting side, quantity and destination. Yongshang Auto can review the application before preparing a product-specific export quotation.