4L0955102 Front Right Headlight Washer Nozzle for AUDI Q7 2010

4L0955102 Front Right Headlight Washer Nozzle Product Overview

The component shown under 4L0955102 is a front right headlight washer nozzle intended for AUDI Q7 2010. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for Q7

Compatibility for 4L0955102 should be confirmed against AUDI Q7 2010 and the right installation side. The review should check the production date where model-year transitions overlap, check whether the original cover is supplied separately from its support, and compare the washer opening beside the correct headlamp. Use the removed part and product photographs to verify nearby parking-sensor or trim interfaces, match the exact model year and bumper revision, and inspect the bumper cutout shape and surrounding contour; finally, use the full OE number, not a partial family reference and retain the removed component for a direct physical comparison.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-107 should be checked separately. For this headlight washer nozzle, review the bracket stiffness and screw seats, compare the depth of the actuator body, and inspect the molded tabs for cracks or distortion. A direct comparison with the removed part should additionally check the bumper-facing surface for transport marks, review the clip geometry on the rear face, and compare the cap perimeter and corner radii. Before the item is accepted, inspect narrow plastic tips before installation and check the complete supplied scope against the photographs.

OE Identification and Side Confirmation

4L0955102 is the primary OE identity for this right front right headlight washer nozzle, while AD02010-107 is the internal item code. Match both references to the vehicle record, then check the washer jet position relative to the headlamp lens. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-107 begins before the bumper area is disturbed: follow the vehicle workshop procedure for bumper removal and keep dirt out of open washer-fluid lines. During trial fitting, confirm sufficient clearance behind the bumper, inspect nearby wiring and sensors before refitting trim, and paint or finish visible covers before final installation when required. Before returning the vehicle to service, check that the washer unit is fully seated in its guide, compare the installed height with the opposite side, and reconnect every hose clip before filling the system.

Receiving Inspection

When AD02010-107 arrives, receiving staff should check molded tabs for whitening, cracks or transport stress, check painted or primed surfaces under neutral lighting, and verify that protective plugs remain in open fluid connections. Before workshop release, document any shortage before the receiving inspection is closed, review the hose spigot for impact damage or distortion, compare connector depth and hose angle with the retained original part, and check the actuator body for straightness before trial installation. Complete the inspection by ensuring that staff inspect the fluid passage only with clean, non-damaging tools, verify the cover contour against the approved product photograph, and confirm the bumper-facing edge has not been compressed in transit.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4L0955102, please request a packing-list breakdown by internal item code, confirm the acceptable delivery window, and send photographs of the removed washer part. Packing instructions should separate left and right items on the packing list, request export-carton dimensions before freight booking, and check carton labels at receiving. Before dispatch, confirm pallet requirements for larger quantities and confirm sample approval before mass shipment.

Frequently Asked Questions

Is a sample order available for 4L0955102?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For item AD02010-107, the approval should state the target vehicle application. The same item record should also list model years and bumper versions for mixed orders.

What should be inspected when 4L0955102 arrives?

Check the item label, side, contour, tabs, fluid connection, supplied components and carton condition before fitting or discarding the packaging. On the listed AUDI Q7 2010, technicians should inspect the rear locator shape without forcing any movable section. A workshop comparison should additionally check the carton partition for evidence of part-to-part contact.

Should the washer system be tested after fitting 4L0955102?

Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. For the right-side order line, reconnect every hose clip before filling the system. The order review should further verify that the cover closes without rubbing the bumper.

Which vehicle application is listed for 4L0955102?

4L0955102 is listed for AUDI Q7 2010. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. The product-specific check for 4L0955102 should match the exact model year and bumper revision. Receiving staff should also use the full OE number, not a partial family reference.

Can 4L0955102 fit every Q7 model year?

No. Styling changes and market equipment can alter washer locations and mounting geometry. Use the listed year and full OE number as the starting point for confirmation. Before this headlight washer nozzle is accepted, compare the hose connection or cover hinge with the original part. Before approval, the buyer or technician should inspect the bumper cutout shape and surrounding contour.