4K0955102B Front Right Headlight Washer Nozzle for AUDI A6 2005

4K0955102B Front Right Headlight Washer Nozzle Product Overview

The component shown under 4K0955102B is a front right headlight washer nozzle intended for AUDI A6 2005. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A6

Compatibility for 4K0955102B should be confirmed against AUDI A6 2005 and the right installation side. The review should match the exact model year and bumper revision, confirm the destination-market equipment specification, and confirm whether a cap, nozzle, bracket or complete assembly is required. Use the removed part and product photographs to check regional variations in headlamp-cleaning equipment, compare every tab, clip seat and locating shoulder, and check the washer jet position relative to the headlamp lens; finally, match the exact model year and bumper revision and confirm the destination-market equipment specification.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-060 should be checked separately. For this headlight washer nozzle, review the clip geometry on the rear face, check whether the visible part requires painting, and inspect the actuator barrel for impact damage. A direct comparison with the removed part should additionally compare the visible bumper-side contour, review the spring-loaded return features where fitted, and check the bumper-facing surface for transport marks. Before the item is accepted, inspect the hose connector for ovality and compare the outer surface profile with the bumper opening.

OE Identification and Side Confirmation

4K0955102B is the primary OE identity for this right front right headlight washer nozzle, while AD02010-060 is the internal item code. Match both references to the vehicle record, then retain the removed component for a direct physical comparison. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-060 begins before the bumper area is disturbed: verify that the cap remains attached through a full washer cycle and check the headlamp lens receives an even spray. During trial fitting, route the washer hose away from sharp edges, inspect nearby wiring and sensors before refitting trim, and complete a final visual check under even lighting. Before returning the vehicle to service, clean the hose and connector before assembly, use hand pressure rather than levering narrow plastic tabs, and transfer reusable clips only after checking their condition.

Receiving Inspection

When AD02010-060 arrives, receiving staff should match the item label to the purchase order and OE reference, inspect the visible cover face for scratches or pressure marks, and check molded tabs for whitening, cracks or transport stress. Before workshop release, confirm the nozzle outlet is clean and unobstructed, review the hose spigot for impact damage or distortion, compare left and right orientation before removing protective wrapping, and verify the cover contour against the approved product photograph. Complete the inspection by ensuring that staff check the spring-return area where the component includes an actuator, inspect the rear locator shape without forcing any movable section, and confirm that loose accessories are identified on the packing list.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4K0955102B, please separate fragile actuator bodies from heavier metal parts, protect hose spigots and projecting tabs, and state any outer-carton marking requirements. Packing instructions should state the target vehicle application, identify painted and unpainted variants on separate lines, and check carton labels at receiving. Before dispatch, send photographs of the removed washer part and request moisture protection for sea freight.

Frequently Asked Questions

Can product photographs alone confirm 4K0955102B compatibility?

Photographs are useful for visual comparison, but the full OE number, vehicle year, bumper version, side and washer equipment must also match. For item AD02010-060, the approval should verify the required left or right installation side. The same item record should also confirm the destination-market equipment specification.

Why must left and right versions of 4K0955102B be distinguished?

Headlight washer components are normally side-specific. Their bumper contours, hose angles, tabs and nozzle directions should not be assumed interchangeable. On the listed AUDI A6 2005, technicians should review the clip geometry on the rear face. A workshop comparison should additionally review the bracket stiffness and screw seats.

Is a sample order available for 4K0955102B?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For the right-side order line, confirm the acceptable delivery window. The order review should further use dividers to prevent caps from rubbing each other.

What information should accompany a 4K0955102B enquiry?

Send the complete OE number, vehicle model and year, installation side, original-part photographs, quantity and delivery destination. The product-specific check for 4K0955102B should check carton labels at receiving. Receiving staff should also state the requested delivery schedule.

Which side uses 4K0955102B?

This front right headlight washer nozzle is catalogued for the right side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. Before this headlight washer nozzle is accepted, compare the distance between mounting points. Before approval, the buyer or technician should check the joint between the visible cap and hidden support.