4G0955102-1 Front Right Headlight Washer Nozzle for AUDI A6 2012

4G0955102-1 Front Right Headlight Washer Nozzle Product Overview

The component shown under 4G0955102-1 is a front right headlight washer nozzle intended for AUDI A6 2012. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A6

Compatibility for 4G0955102-1 should be confirmed against AUDI A6 2012 and the right installation side. The review should retain the removed component for a direct physical comparison, check whether the bumper is standard or sport specification, and check the washer jet position relative to the headlamp lens. Use the removed part and product photographs to match the connector and fluid inlet position where applicable, compare the actuator orientation behind the bumper cover, and compare the washer opening beside the correct headlamp; finally, separate mirrored left and right items during inventory selection and compare every tab, clip seat and locating shoulder.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-056 should be checked separately. For this headlight washer nozzle, compare the distance between mounting points, inspect the washer outlet for blockage, and check each molded locator against the original component. A direct comparison with the removed part should additionally review the bracket stiffness and screw seats, compare the retracted position with the bumper surface, and inspect the molded tabs for cracks or distortion. Before the item is accepted, check the cap hinge or retaining point and review the clip geometry on the rear face.

OE Identification and Side Confirmation

4G0955102-1 is the primary OE identity for this right front right headlight washer nozzle, while AD02010-056 is the internal item code. Match both references to the vehicle record, then separate mirrored left and right items during inventory selection. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-056 begins before the bumper area is disturbed: check the headlamp lens receives an even spray and work with the washer system depressurized. During trial fitting, confirm that the nozzle extends and retracts freely, verify that the cap remains attached through a full washer cycle, and check that the washer unit is fully seated in its guide. Before returning the vehicle to service, photograph the original routing before disassembly, protect the painted bumper surface during removal, and check the system for leaks after reconnection.

Receiving Inspection

When AD02010-056 arrives, receiving staff should compare connector depth and hose angle with the retained original part, verify the nozzle head returns smoothly without applying excess force, and compare connector depth and hose angle with the retained original part. Before workshop release, verify the nozzle head returns smoothly without applying excess force, compare connector depth and hose angle with the retained original part, verify the nozzle head returns smoothly without applying excess force, and compare connector depth and hose angle with the retained original part. Complete the inspection by ensuring that staff verify the nozzle head returns smoothly without applying excess force, compare connector depth and hose angle with the retained original part, and verify the nozzle head returns smoothly without applying excess force.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4G0955102-1, please include the full OE reference on the purchase order, confirm whether caps and nozzles should be supplied as pairs, and use dividers to prevent caps from rubbing each other. Packing instructions should send photographs of the removed washer part, state the target vehicle application, and separate fragile actuator bodies from heavier metal parts. Before dispatch, provide the complete destination address or port and request export-carton dimensions before freight booking.

Frequently Asked Questions

How should 4G0955102-1 be packed for export?

The front right headlight washer nozzle should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. For item AD02010-056, the approval should protect hose spigots and projecting tabs. The same item record should also state the requested delivery schedule.

Which side uses 4G0955102-1?

This front right headlight washer nozzle is catalogued for the right side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. On the listed AUDI A6 2012, technicians should compare the visible bumper-side contour. A workshop comparison should additionally check the joint between the visible cap and hidden support.

Does the finish specification matter for 4G0955102-1?

Yes. A visible headlight washer nozzle may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. For the right-side order line, check the fluid inlet for storage contamination. The order review should further compare the depth of the actuator body.

Should the washer system be tested after fitting 4G0955102-1?

Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. The product-specific check for 4G0955102-1 should check that the washer unit is fully seated in its guide. Receiving staff should also inspect nearby wiring and sensors before refitting trim.

How should 4G0955102-1 be checked before installation?

Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. Before this headlight washer nozzle is accepted, review facelift and pre-facelift washer layouts. Before approval, the buyer or technician should check regional variations in headlamp-cleaning equipment.