4G0955101-1 Front Left Headlight Washer Nozzle for AUDI A6 2012

4G0955101-1 Front Left Headlight Washer Nozzle Product Overview

The component shown under 4G0955101-1 is a front left headlight washer nozzle intended for AUDI A6 2012. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A6

Compatibility for 4G0955101-1 should be confirmed against AUDI A6 2012 and the left installation side. The review should check whether the bumper is standard or sport specification, check whether the original cover is supplied separately from its support, and confirm whether a cap, nozzle, bracket or complete assembly is required. Use the removed part and product photographs to confirm that the vehicle is equipped with a factory headlight washer system, match the connector and fluid inlet position where applicable, and compare the hose connection or cover hinge with the original part; finally, use the full OE number, not a partial family reference and check regional variations in headlamp-cleaning equipment.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-055 should be checked separately. For this headlight washer nozzle, review the spring-loaded return features where fitted, check the fluid inlet for storage contamination, and inspect narrow plastic tips before installation. A direct comparison with the removed part should additionally compare the depth of the actuator body, review the sealing area around the hose connection, and check whether the visible part requires painting. Before the item is accepted, inspect the rear reinforcement ribs and compare the distance between mounting points.

OE Identification and Side Confirmation

4G0955101-1 is the primary OE identity for this left front left headlight washer nozzle, while AD02010-055 is the internal item code. Match both references to the vehicle record, then inspect the bumper cutout shape and surrounding contour. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-055 begins before the bumper area is disturbed: paint or finish visible covers before final installation when required and verify that the cover closes without rubbing the bumper. During trial fitting, confirm that no hose is pinched behind the bumper, protect the painted bumper surface during removal, and route the washer hose away from sharp edges. Before returning the vehicle to service, clean the hose and connector before assembly, follow the vehicle workshop procedure for bumper removal, and check that the washer unit is fully seated in its guide.

Receiving Inspection

When AD02010-055 arrives, receiving staff should verify the cover contour against the approved product photograph, check the cap hinge or retaining point for free movement, and compare the supplied side with the vehicle repair order. Before workshop release, check painted or primed surfaces under neutral lighting, inspect projecting pins before placing the item on a hard bench, confirm the nozzle outlet is clean and unobstructed, and photograph the received item if the vehicle fitment is still pending. Complete the inspection by ensuring that staff document any shortage before the receiving inspection is closed, inspect the rear locator shape without forcing any movable section, and compare the visible surface texture with the ordered specification.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4G0955101-1, please request replacement-part documentation when required, confirm whether the visible cover needs a primed or finished surface, and confirm whether caps and nozzles should be supplied as pairs. Packing instructions should state the requested delivery schedule, identify painted and unpainted variants on separate lines, and separate left and right items on the packing list. Before dispatch, request barcode or private-label details when needed and use dividers to prevent caps from rubbing each other.

Frequently Asked Questions

Is a sample order available for 4G0955101-1?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For item AD02010-055, the approval should include the full OE reference on the purchase order. The same item record should also protect each nozzle outlet from dust during transit.

Which vehicle application is listed for 4G0955101-1?

4G0955101-1 is listed for AUDI A6 2012. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. On the listed AUDI A6 2012, technicians should confirm the front bumper option before ordering. A workshop comparison should additionally match the connector and fluid inlet position where applicable.

Does the finish specification matter for 4G0955101-1?

Yes. A visible headlight washer nozzle may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. For the left-side order line, check the joint between the visible cap and hidden support. The order review should further compare the cap-to-support engagement method.

Are clips, hoses or fasteners supplied with 4G0955101-1?

The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. The product-specific check for 4G0955101-1 should confirm the acceptable delivery window. Receiving staff should also separate left and right items on the packing list.

Which side uses 4G0955101-1?

This front left headlight washer nozzle is catalogued for the left side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. Before this headlight washer nozzle is accepted, check the joint between the visible cap and hidden support. Before approval, the buyer or technician should check the cap hinge or retaining point.