3M51-R218A14-AB Exterior Door Handle Cap with Keyhole for 2009 Ford Focus
Primary OE reference: 3M51-R218A14-AB
Cross-reference 1: 3M51-R218A14-AB
Product type: Exterior Door Handle Cap with Keyhole
Applicable vehicle: 2009 FORD Focus
Installation position: Exterior door-handle end cap with lock access
Brand: FORD
Model: Focus
Vehicle year: 2009
Visible identification: Short tapered cap with a circular key-cylinder opening
Surface appearance: Paintable exterior cap; saved images show multiple colour references
Physical comparison: Match the keyhole diameter, rear clips and outer taper with the existing Focus handle assembly.
Mounting review: Compare the pivot, clips, linkage or electrical connector shown in the saved product images.
Installation preparation: Dry-fit around the lock cylinder and verify the cap sits flush before engaging its concealed retainers.
Order information: Quote 3M51-R218A14-AB, SKU FD02037-005, exterior door-handle end cap with lock access and required quantity.
Wholesale note: State destination, packaging preference and whether matching left/right components are required.
Exterior Door Handle Cap with Keyhole Application
OE 3M51-R218A14-AB covers the exterior door-handle end cap with lock access application listed for 2009 FORD Focus. It is a dedicated exterior door handle cap with keyhole, not a universal replacement chosen by appearance.
Visible Profile and Component Identity
Photographs document short tapered cap with a circular key-cylinder opening. Also note the paintable exterior cap; saved images show multiple colour references, then verify every concealed fastening feature against the removed component.
Product-Specific Selection Notes
A keyed cap must centre cleanly around the lock barrel while continuing the handle contour. Compare the amount of material above and below the opening, because a cap from another door-handle family may accept the cylinder yet leave an uneven body gap.
Surface and Workshop Handling
For 3M51-R218A14-AB, protect the visible paintable exterior cap; saved images show multiple colour references during bench preparation. Avoid solvents that attack moulded plastic, and do not apply paint or adhesive to the lever pivot, switch membrane or retaining clips.
Latch or Electrical Interface
Before tightening FD02037-005, inspect the latch rod or cable end, pivot pin and return spring for wear. The handle should move the latch through its full travel without side-loading the carrier or scraping the surrounding panel.
Related System Diagnosis
When FD02037-005 will not sit flush, check the reusable carrier and every clip seat for deformation before forcing 3M51-R218A14-AB into place. A distorted base or trapped paint edge can create a visible gap even when the decorative cover is correct.
Packaging for Trade Orders
For bulk packing, place FD02037-005 in an individual sleeve with the visible face separated from fasteners and adjacent handles. Mark exterior door-handle end cap with lock access on the outer label so mirrored or different-door components remain distinguishable during warehouse picking.
Vehicle and Position Confirmation
Match the keyhole diameter, rear clips and outer taper with the existing Focus handle assembly. For 3M51-R218A14-AB, confirm 2009 production timing and the exterior door-handle end cap with lock access designation; the wrong neighbour part may reverse a pivot, cable seat, lock opening or connector.
Automotive Replacement Part Specifications
| Product type | Exterior Door Handle Cap with Keyhole |
|---|---|
| Primary OE reference | 3M51-R218A14-AB |
| Internal item code | FD02037-005 |
| Vehicle brand | FORD |
| Model | Focus |
| Vehicle year | 2009 |
| Applicable vehicle | 2009 FORD Focus |
| Installation position | Exterior door-handle end cap with lock access |
| Surface appearance | Paintable exterior cap; saved images show multiple colour references |
| Cross-reference numbers | 3M51-R218A14-AB |
Installation and Functional Check
Dry-fit around the lock cylinder and verify the cap sits flush before engaging its concealed retainers. Once 3M51-R218A14-AB is seated, cycle the mechanism by hand, observe its return position and make sure nearby trim is not loaded or scratched.
Receiving and Trade Supply
A trade enquiry for FD02037-005 should state 3M51-R218A14-AB, 2009 FORD Focus, exterior door-handle end cap with lock access, the required finish and order quantity. Receiving staff can identify this exact line by comparing short tapered cap with a circular key-cylinder opening with the delivered item.
Frequently Asked Questions
What component is numbered 3M51-R218A14-AB?
The number refers here to a exterior door handle cap with keyhole for the stated FORD Focus application.
What needs comparing with the old part?
Match short tapered cap with a circular key-cylinder opening, followed by every rear attachment and operating connection.
Can paint colour confirm fitment?
No. Surface colour alone does not prove that the carrier, lock feature or linkage is correct.
When is the functional test performed?
Perform a dry test before replacing all trim, then confirm normal return after final tightening.
How is FD02037-005 ordered in quantity?
Specify 3M51-R218A14-AB, the exterior door-handle end cap with lock access, finish, packing preference and shipment destination.
