34500-T7J-H01 Rear Bumper Light for HONDA Vezel 2014 Right
Primary OE reference: 34500-T7J-H01
Product type: Rear Bumper Light
Applicable vehicle: HONDA Vezel 2014
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: HONDA
Model: Vezel
Vehicle year: 2014
Physical comparison: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical check: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Installation guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
Wholesale enquiry: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
34500-T7J-H01 Rear Bumper Light Overview
This product is listed for HONDA Vezel 2014 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
Use the removed component as the physical reference for outer shape, housing projection and clip location.
Before approving the Vezel part for packing, record the approved side and vehicle application for repeat-order identification so the lens and housing are supported without distortion.
Rear-Bumper Geometry Review
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
Before fitting the right unit, confirm that the cable exit, where fitted, clears the bumper reinforcement so a passive reflector is not confused with an illuminated assembly.
While the HONDA bumper opening is accessible, confirm that any connector seal remains square when the housing is fully seated to verify that the photographed configuration matches the vehicle in the workshop.
Lens, Housing and Harness Comparison
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
During comparison of the HONDA rear component, use the opposite-side component only as an alignment reference, not as an interchange part to avoid contact with wiring, body edges or hot exhaust components.
For a repeat order of the right version, compare the outer lens edge with the moulded bumper recess to keep the optical face level with the surrounding painted surface.
Installation Completion
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
On the 2014 Vezel bumper layout, inspect the lower valance and nearby exhaust trim for adequate operating clearance before any modification is made to the bumper or replacement part.
At the workshop selection stage for Vezel, check the rear housing projection against the space behind the bumper skin before deciding whether original hardware is suitable for reuse.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 34500-T7J-H01 |
| Cross-reference numbers | 34500-T7J-H01 |
| Internal item code | HD04004-087 |
| Vehicle brand | HONDA |
| Vehicle model | Vezel |
| Model year | 2014 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
The visible face should remain separated from tape, staples and loose hardware throughout transport.
At the right rear-bumper position, compare the bumper corner radius with the product face from more than one viewing angle because facelift bumpers can retain the same vehicle name with different apertures.
When reviewing the 2014 vehicle, align each locating tab with the matching slot before applying hand pressure so left- and right-hand stock cannot be mixed during consolidation.
Frequently Asked Questions
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Request a Product-Specific Quote
The sales team can check whether accessories shown in the photograph are part of the requested scope.
