34500-SYJ-H01 Rear Bumper Light for HONDA Elysion 2013 Right
Primary OE reference: 34500-SYJ-H01
Product type: Rear Bumper Light
Applicable vehicle: HONDA Elysion 2013
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: HONDA
Model: Elysion
Vehicle year: 2013
Shape and clips: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Rear visibility role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Powered-version check: Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Workshop guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
Quotation details: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.
Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
34500-SYJ-H01 Rear Bumper Light Overview
This product is listed for HONDA Elysion 2013 at the right rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
For this Elysion body configuration, protect the visible surface until the full perimeter gap has been accepted so the visible gap remains even after every retaining point is engaged.
Bumper Opening and Vehicle Match
Review the corner radius, edge return and rear fastening points against the original bumper opening.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Before approving the Elysion part for packing, review the reflector texture and lens colour in neutral workshop light so the lens and housing are supported without distortion.
Before fitting the right unit, record the approved side and vehicle application for repeat-order identification so a passive reflector is not confused with an illuminated assembly.
Lens Construction and Powered Variants
Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.
While the HONDA bumper opening is accessible, confirm that the cable exit, where fitted, clears the bumper reinforcement to verify that the photographed configuration matches the vehicle in the workshop.
During comparison of the HONDA rear component, confirm that any connector seal remains square when the housing is fully seated to avoid contact with wiring, body edges or hot exhaust components.
Mounting and Final Verification
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.
For a repeat order of the right version, use the opposite-side component only as an alignment reference, not as an interchange part to keep the optical face level with the surrounding painted surface.
On the 2013 Elysion bumper layout, compare the outer lens edge with the moulded bumper recess before any modification is made to the bumper or replacement part.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 34500-SYJ-H01 |
| Cross-reference numbers | 34500-SYJ-H01 |
| Internal item code | HD04004-110 |
| Vehicle brand | HONDA |
| Vehicle model | Elysion |
| Model year | 2013 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
At the workshop selection stage for Elysion, inspect the lower valance and nearby exhaust trim for adequate operating clearance before deciding whether original hardware is suitable for reuse.
At the right rear-bumper position, check the rear housing projection against the space behind the bumper skin because facelift bumpers can retain the same vehicle name with different apertures.
Frequently Asked Questions
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Request a Product-Specific Quote
Provide the expected order quantity to receive a trade-oriented packing and supply proposal.
