33555-SLG-H01 Rear Bumper Light for HONDA Odyssey 2009 Left
Primary OE reference: 33555-SLG-H01
Product type: Rear Bumper Light
Applicable vehicle: HONDA Odyssey 2009
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: HONDA
Model: Odyssey
Vehicle year: 2009
Housing match: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.
Reflector or lamp role: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
Wiring confirmation: If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.
Mounting sequence: After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
Purchase information: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
33555-SLG-H01 Rear Bumper Light Overview
This product is listed for HONDA Odyssey 2009 at the left rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
During comparison of the HONDA rear component, use the opposite-side component only as an alignment reference, not as an interchange part before any modification is made to the bumper or replacement part.
Application and Rear-Bumper Position
Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
For a repeat order of the left version, compare the outer lens edge with the moulded bumper recess before deciding whether original hardware is suitable for reuse.
On the 2009 Odyssey bumper layout, inspect the lower valance and nearby exhaust trim for adequate operating clearance because facelift bumpers can retain the same vehicle name with different apertures.
Optical Face and Connector Review
If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.
Protect the exposed face from tools and fasteners while the bumper liner is open for access.
At the workshop selection stage for Odyssey, check the rear housing projection against the space behind the bumper skin so left- and right-hand stock cannot be mixed during consolidation.
At the left rear-bumper position, compare the bumper corner radius with the product face from more than one viewing angle so the approved product can be picked consistently in a mixed wholesale order.
Workshop Fitting Sequence
After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.
Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.
When reviewing the 2009 vehicle, align each locating tab with the matching slot before applying hand pressure so hidden brackets are not loaded or bent during installation.
For the HONDA Odyssey application, check whether the original component uses a separate retainer or an integral locking tab to preserve access for a final electrical test where a lamp circuit is present.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 33555-SLG-H01 |
| Cross-reference numbers | 33555-SLG-H01 |
| Internal item code | HD04004-103 |
| Vehicle brand | HONDA |
| Vehicle model | Odyssey |
| Model year | 2009 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
For this Odyssey body configuration, verify the fastener direction and the shape of the concealed support frame to reduce clip damage during a no-force trial installation.
Before approving the Odyssey part for packing, protect the visible surface until the full perimeter gap has been accepted to prevent a visually similar version from sitting proud of the bumper.
Frequently Asked Questions
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Is this component illuminated or reflector-only?
Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Request a Product-Specific Quote
A product-specific quotation can be prepared after the vehicle, side and destination are confirmed.
