1K8 945 106 Rear Bumper Light for VOLKSWAGEN Scirocco 2009 Right
Primary OE reference: 1K8 945 106
Product type: Rear Bumper Light
Applicable vehicle: VOLKSWAGEN Scirocco 2009
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: VOLKSWAGEN
Model: Scirocco
Vehicle year: 2009
Physical comparison: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical check: Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Installation guidance: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.
Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
Wholesale enquiry: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.
Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
1K8 945 106 Rear Bumper Light Overview
This product is listed for VOLKSWAGEN Scirocco 2009 at the right rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
When reviewing the 2009 vehicle, confirm that any connector seal remains square when the housing is fully seated so the approved product can be picked consistently in a mixed wholesale order.
Physical Fitment Evidence
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
For the VOLKSWAGEN Scirocco application, use the opposite-side component only as an alignment reference, not as an interchange part so hidden brackets are not loaded or bent during installation.
For this Scirocco body configuration, compare the outer lens edge with the moulded bumper recess to preserve access for a final electrical test where a lamp circuit is present.
Surface, Seal and Electrical Interface
Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.
Before approving the Scirocco part for packing, inspect the lower valance and nearby exhaust trim for adequate operating clearance to reduce clip damage during a no-force trial installation.
Before fitting the right unit, check the rear housing projection against the space behind the bumper skin to prevent a visually similar version from sitting proud of the bumper.
Bumper Assembly Check
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.
While the VOLKSWAGEN bumper opening is accessible, compare the bumper corner radius with the product face from more than one viewing angle before the packaging and carton marking are finalized.
During comparison of the VOLKSWAGEN rear component, align each locating tab with the matching slot before applying hand pressure before inner liners make the rear attachment points difficult to inspect.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 1K8 945 106 |
| Cross-reference numbers | 1K8 945 106 |
| Internal item code | VM04004-006 |
| Vehicle brand | VOLKSWAGEN |
| Vehicle model | Scirocco |
| Model year | 2009 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
The visible face should remain separated from tape, staples and loose hardware throughout transport.
For a repeat order of the right version, check whether the original component uses a separate retainer or an integral locking tab so the visible gap remains even after every retaining point is engaged.
On the 2009 Scirocco bumper layout, verify the fastener direction and the shape of the concealed support frame so the lens and housing are supported without distortion.
Frequently Asked Questions
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Request a Product-Specific Quote
Clear application details allow the sales team to separate reflector and illuminated versions in the offer.
