1K8 945 105B Rear Bumper Light for VOLKSWAGEN Scirocco 2013 Left
Primary OE reference: 1K8 945 105B
Product type: Rear Bumper Light
Applicable vehicle: VOLKSWAGEN Scirocco 2013
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: VOLKSWAGEN
Model: Scirocco
Vehicle year: 2013
Housing match: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Reflector or lamp role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Wiring confirmation: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Mounting sequence: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
Purchase information: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
1K8 945 105B Rear Bumper Light Overview
This product is listed for VOLKSWAGEN Scirocco 2013 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
For the VOLKSWAGEN Scirocco application, compare the outer lens edge with the moulded bumper recess so hidden brackets are not loaded or bent during installation.
Application and Rear-Bumper Position
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
For this Scirocco body configuration, inspect the lower valance and nearby exhaust trim for adequate operating clearance to preserve access for a final electrical test where a lamp circuit is present.
Before approving the Scirocco part for packing, check the rear housing projection against the space behind the bumper skin to reduce clip damage during a no-force trial installation.
Optical Face and Connector Review
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
Before fitting the left unit, compare the bumper corner radius with the product face from more than one viewing angle to prevent a visually similar version from sitting proud of the bumper.
While the VOLKSWAGEN bumper opening is accessible, align each locating tab with the matching slot before applying hand pressure before the packaging and carton marking are finalized.
Workshop Fitting Sequence
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
During comparison of the VOLKSWAGEN rear component, check whether the original component uses a separate retainer or an integral locking tab before inner liners make the rear attachment points difficult to inspect.
For a repeat order of the left version, verify the fastener direction and the shape of the concealed support frame so the visible gap remains even after every retaining point is engaged.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 1K8 945 105B |
| Cross-reference numbers | 1K8 945 105B |
| Internal item code | VM04004-003 |
| Vehicle brand | VOLKSWAGEN |
| Vehicle model | Scirocco |
| Model year | 2013 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
On the 2013 Scirocco bumper layout, protect the visible surface until the full perimeter gap has been accepted so the lens and housing are supported without distortion.
At the workshop selection stage for Scirocco, review the reflector texture and lens colour in neutral workshop light so a passive reflector is not confused with an illuminated assembly.
Frequently Asked Questions
What should be tested after fitting?
Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
Why can the same model year use another version?
Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Request a Product-Specific Quote
Yongshang Auto can review the pictured configuration before preparing a quantity-based offer.
