C1BB-13W029-BH Head Light for FORD Fiesta 2013 Right
Primary OE reference: C1BB-13W029-BH
Cross-reference number 1: C1BB-13W029-BH
Product type: Head Light Assembly
Applicable vehicle: FORD Fiesta 2013
Installation position: Right front headlamp position
Brand: FORD
Model: Fiesta
Vehicle year: 2013
Lighting configuration: projector-equipped optics, projector optics, European-market specification
Housing comparison: Check the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate neighbouring variants.
Optical system: Cross-check the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.
Electrical interface: Do not use connector colour as the only selection point; terminal geometry, locking tabs and installed modules must also agree.
Mounting points: Check mounting-ear spacing and support height against the removed lamp, including any hidden guide pin behind the bumper or grille edge.
Installation guidance: Complete a no-force trial fit first; once the panel gaps are even, secure the unit and adjust the beam to workshop specifications.
Wholesale packing: Mixed orders should determine vehicle application and side clearly, with protective packing around the optical face and electrical connections.
Application-specific focus: For the right FORD Fiesta application with projector-equipped optics, projector optics, european-market specification, look over the lens pattern, internal bezel finish and optical modules so the specified unit matches the intended lighting package.
Head Light Assembly Overview
This product record supports physical comparison of a front lamp assembly for workshop replacement and wholesale purchasing. It is catalogued under OE reference C1BB-13W029-BH for FORD Fiesta 2013, with the right position identified in the source record.
The external lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Compare the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.
For the Fiesta application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use non-matching internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Review the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate adjacent variants.
Review mounting-ear spacing and support height against the removed lamp, including any hidden guide pin behind the bumper or grille edge.
Connector and Control Hardware
Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
Establish the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
Tighten the fasteners evenly, restore nearby covers only after functional testing, and verify bonnet and bumper clearances one final time.
A qualified workshop should inspect surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | C1BB-13W029-BH |
| Cross-reference numbers | C1BB-13W029-BH |
| Internal item code | FD04001-128 |
| Vehicle brand | FORD |
| Vehicle model | Fiesta |
| Model year | 2013 |
| Installation position | Right front |
| Lighting configuration | projector-equipped optics, projector optics, European-market specification |
Wholesale Supply and Protective Packing
Packing should distribute load around the housing rather than the lens and preserve dry, clean connector and module interfaces.
When requesting a quotation, include the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this right FORD Fiesta headlamp, the projector-equipped optics, projector optics, european-market specification specification should be assessed together with the 2013 body application. Establish that the headlamp sits naturally in the body opening and follows the bonnet, grille and fender lines without forced alignment.
The right Fiesta lighting package should remain the reference during electrical review. The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.
When fitting the FORD Fiesta unit at the right front position, preserve even body gaps and the intended beam orientation. After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.
Frequently Asked Questions
What information supports a wholesale quotation?
State the FORD Fiesta application, production year, right side, lighting version, quantity and delivery country.
How should headlamp fitment be confirmed?
For the right Fiesta lamp, compare the body outline, mounting tabs, connector and lighting technology with the removed unit. Model year alone may not distinguish every trim.
Are left and right headlamps interchangeable?
No. This application requires the right side; bracket geometry, optical pattern and wiring position are side-specific.
When is professional beam aiming required?
Beam alignment should be checked after the unit is secured and every lighting function has been tested.
What photographs are useful for comparison?
Clear front, rear, connector and mounting-tab views help distinguish the required headlamp from a similar-looking alternative.
