92101-K6040 Head Light for HYUNDAI i10 2021 Left
Primary OE reference: 92101-K6040
Cross-reference number 1: 92101-K6040
Product type: Head Light Assembly
Applicable vehicle: HYUNDAI i10 2021
Installation position: Left front headlamp position
Brand: HYUNDAI
Model: i10
Vehicle year: 2021
Lighting configuration: standard equipment version
Housing comparison: Use the original assembly to check the shell profile, upper support shape and clearance around surrounding trim before installation.
Optical system: Determine whether the original lighting system uses a reflector, projector, halogen bulb, xenon burner or integrated LED light source.
Electrical interface: Do not use connector colour as the only selection point; terminal geometry, locking tabs and installed modules must also agree.
Mounting points: Start all fasteners loosely during the trial fit and make sure the housing rests against its supports without bending a bracket.
Installation guidance: Complete a no-force trial fit first; once the panel gaps are even, secure the unit and adjust the beam to workshop specifications.
Wholesale packing: For repeat orders, keep the approved product photographs and application record so the same optical and mounting version is chosen.
Application-specific focus: For the left HYUNDAI i10 application with standard equipment version, validate that the beam system and visible lamp signature correspond to the vehicle trim rather than selecting by exterior outline alone.
Head Light Assembly Overview
The photographed assembly is supplied for buyers comparing a complete front lighting unit by vehicle application and physical construction. It is catalogued under OE reference 92101-K6040 for HYUNDAI i10 2021, with the left position identified in the source record.
The visible lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Identify whether the original lighting system uses a reflector, projector, halogen bulb, xenon burner or integrated LED light source.
For the i10 application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use non-matching internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Inspect the inner and outer corners of the housing as well as the gap to adjacent panels; these points often separate nearby variants.
Start all fasteners loosely during the trial fit and make sure the housing rests against its supports without bending a bracket.
Connector and Control Hardware
Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
Verify the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
Use recommended workshop procedures for removal and refitting, then validate that vibration, panel pressure and cable routing do not stress the housing.
A qualified workshop should review surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | 92101-K6040 |
| Cross-reference numbers | 92101-K6040 |
| Internal item code | HY04001-307 |
| Vehicle brand | HYUNDAI |
| Vehicle model | i10 |
| Model year | 2021 |
| Installation position | Left front |
| Lighting configuration | standard equipment version |
Wholesale Supply and Protective Packing
For repeat orders, retain the approved product photographs and application record so the same optical and mounting version is requested.
When requesting a quotation, state the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this left HYUNDAI i10 headlamp, the standard equipment version specification should be assessed together with the 2021 body application. Review the complete lamp body from several angles because a similar lens can conceal a non-matching rear casing or bracket offset.
The left i10 lighting package should remain the reference during electrical review. Align with the connector key, pin arrangement, latch direction and cable exit; LED or xenon versions may also require compatible control hardware.
When fitting the HYUNDAI i10 unit at the left front position, preserve even body gaps and the intended beam orientation. After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.
Frequently Asked Questions
How should headlamp fitment be confirmed?
For the left i10 lamp, compare the body outline, mounting tabs, connector and lighting technology with the removed unit. Model year alone may not distinguish every trim.
What photographs are useful for comparison?
Clear front, rear, connector and mounting-tab views help distinguish the required headlamp from a similar-looking alternative.
What should be checked before installation?
For the i10, review the vehicle supports, compare every fixing point, verify the connector and complete a no-force trial fit.
Why must the rear housing be compared?
A similar lens can conceal a non-matching casing depth, cap arrangement or bracket offset, preventing correct seating in the body opening.
How can connector compatibility be reviewed?
Compare keying, terminal count, latch direction and wire exit, then identify any required ballast, driver or levelling motor.
