92101-0X020 Head Light for HYUNDAI i10 2007 Left
Primary OE reference: 92101-0X020
Cross-reference number 1: 92101-0X020
Product type: Head Light Assembly
Applicable vehicle: HYUNDAI i10 2007
Installation position: Left front headlamp position
Brand: HYUNDAI
Model: i10
Vehicle year: 2007
Lighting configuration: power-adjustment version
Housing comparison: Confirm that the headlamp sits naturally in the body opening and follows the bonnet, grille and fender lines without forced alignment.
Optical system: Look over the lens pattern, internal bezel finish and optical modules so the requested unit matches the intended lighting package.
Electrical interface: Confirm compatibility with the vehicle’s lighting controls, especially where automatic levelling or daytime-running-light functions are fitted.
Mounting points: Shield projecting tabs during handling and verify that each locating feature enters the correct body-side slot during the dry fit.
Installation guidance: Complete a no-force trial fit first; once the panel gaps are even, secure the unit and adjust the beam to workshop specifications.
Wholesale packing: For repeat orders, retain the approved product photographs and application record so the same optical and mounting version is requested.
Application-specific focus: For the left HYUNDAI i10 application with power-adjustment version, verify reflector colour, projector presence and any decorative internal trim before approving a left/right pair for one vehicle.
Head Light Assembly Overview
The headlamp shown should be selected as a complete vehicle-specific assembly, with side and lighting version confirmed before ordering. It is catalogued under OE reference 92101-0X020 for HYUNDAI i10 2007, with the left position identified in the source record.
The visible lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Review the lens pattern, internal bezel finish and optical modules so the requested unit matches the intended lighting package.
For the i10 application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use different internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Lay the replacement beside the removed unit and cross-check overall depth, edge returns, vent locations and rear-cover clearance.
Shield projecting tabs during handling and verify that each locating feature enters the correct body-side slot during the dry fit.
Connector and Control Hardware
Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
Verify the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
Use approved workshop procedures for removal and refitting, then confirm that vibration, panel pressure and cable routing do not stress the housing.
A qualified workshop should review surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | 92101-0X020 |
| Cross-reference numbers | 92101-0X020 |
| Internal item code | HY04001-295 |
| Vehicle brand | HYUNDAI |
| Vehicle model | i10 |
| Model year | 2007 |
| Installation position | Left front |
| Lighting configuration | power-adjustment version |
Wholesale Supply and Protective Packing
Carton protection should prevent abrasion on the lens and impact loading on brackets, caps, adjusters or exposed control modules.
When requesting a quotation, supply the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this left HYUNDAI i10 headlamp, the power-adjustment version specification should be assessed together with the 2007 body application. Review the complete lamp body from several angles because a similar lens can conceal a different rear casing or bracket offset.
The left i10 lighting package should remain the reference during electrical review. Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
When fitting the HYUNDAI i10 unit at the left front position, preserve even body gaps and the intended beam orientation. Complete a no-force trial fit first; once the panel gaps are even, secure the unit and adjust the beam to workshop specifications.
Frequently Asked Questions
What should be checked before installation?
For the i10, review the vehicle supports, cross-check every fixing point, verify the connector and complete a no-force trial fit.
What distinguishes neighbouring lighting variants?
Reflector, projector, xenon and LED versions can differ in modules, daytime-light layout, internal bezel and plug configuration.
When is professional beam aiming required?
Beam alignment should be checked after the unit is secured and every lighting function has been tested.
Are bulbs and electronic modules included?
The included components are those visible in the product photographs. Verify bulbs, caps, motors, ballasts and LED modules separately.
What photographs are useful for comparison?
Clear front, rear, connector and mounting-tab views help distinguish the required headlamp from a similar-looking alternative.
