92102-05510 Head Light for HYUNDAI Atos 2004 Right
Primary OE reference: 92102-05510
Cross-reference number 1: 92102-05510
Product type: Head Light Assembly
Applicable vehicle: HYUNDAI Atos 2004
Installation position: Right front headlamp position
Brand: HYUNDAI
Model: Atos
Vehicle year: 2004
Lighting configuration: Align with the photographed optical configuration
Housing comparison: Lay the replacement beside the removed unit and review overall depth, edge returns, vent locations and rear-cover clearance.
Optical system: Confirm that the beam system and photographed lamp signature correspond to the vehicle trim rather than selecting by exterior outline alone.
Electrical interface: Align with the connector key, pin arrangement, latch direction and cable exit; LED or xenon versions may also require compatible control hardware.
Mounting points: A correct assembly should align at the locating points without drilling, trimming or forcing the vehicle-side brackets.
Installation guidance: Keep wiring clear of hot or moving components, then test low beam, high beam, indicator and daytime lighting where applicable.
Wholesale packing: For wholesale supply, the lens should be isolated from carton pressure while the rear shell, adjusters and projecting mounting tabs are supported.
Application-specific focus: For the right HYUNDAI Atos application with align with the photographed optical configuration, examine the lens pattern, internal bezel finish and optical modules so the chosen unit matches the intended lighting package.
Head Light Assembly Overview
The listed unit is designed for the stated vehicle position and should be matched to the removed headlamp before installation. It is catalogued under OE reference 92102-05510 for HYUNDAI Atos 2004, with the right position identified in the source record.
The observable lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.
Lighting Function and Optical Configuration
Confirm that the beam system and photographed lamp signature correspond to the vehicle trim rather than selecting by exterior outline alone.
For the Atos application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use distinct internal modules, beam controls and daytime-light signatures.
Vehicle Fitment and Body Interface
Cross-check the rear housing depth, outer lens contour and the relationship between the grille-side and fender-side edges with the removed lamp.
A correct assembly should align at the locating points without drilling, trimming or forcing the vehicle-side brackets.
Connector and Control Hardware
The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.
Confirm the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.
Installation and Beam Alignment
After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.
A qualified workshop should inspect surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.
Automotive Lighting Product Specifications
| Product type | Head Light Assembly |
|---|---|
| Primary OE reference | 92102-05510 |
| Cross-reference numbers | 92102-05510 |
| Internal item code | HY04001-006 |
| Vehicle brand | HYUNDAI |
| Vehicle model | Atos |
| Model year | 2004 |
| Installation position | Right front |
| Lighting configuration | Match the photographed optical configuration |
Wholesale Supply and Protective Packing
Carton protection should prevent abrasion on the lens and impact loading on brackets, caps, adjusters or exposed control modules.
When requesting a quotation, state the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.
Application-Specific Comparison Notes
For this right HYUNDAI Atos headlamp, the align with the photographed optical configuration specification should be assessed together with the 2004 body application. Use the original assembly to inspect the shell profile, upper support shape and clearance around neighbouring trim before installation.
The right Atos lighting package should remain the reference during electrical review. Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.
When fitting the HYUNDAI Atos unit at the right front position, preserve even body gaps and the intended beam orientation. Use approved workshop procedures for removal and refitting, then verify that vibration, panel pressure and cable routing do not stress the housing.
Frequently Asked Questions
Can a headlamp be chosen by appearance alone?
No. The right lamp must also align with the optical system, electrical interface, mounting features and market specification.
When is professional beam aiming required?
Beam alignment should be checked after the unit is secured and every lighting function has been tested.
How should headlamp fitment be confirmed?
For the right Atos lamp, cross-check the body outline, mounting tabs, connector and lighting technology with the removed unit. Model year alone may not distinguish every trim.
Why must the rear housing be compared?
A similar lens can conceal a distinct casing depth, cap arrangement or bracket offset, preventing correct seating in the body opening.
What photographs are useful for comparison?
Clear front, rear, connector and mounting-tab views help distinguish the required headlamp from a similar-looking alternative.
