7P6 945 105A Rear Bumper Light for VOLKSWAGEN Touareg 2015 Left
Primary OE reference: 7P6 945 105A
Product type: Rear Bumper Light
Applicable vehicle: VOLKSWAGEN Touareg 2015
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: VOLKSWAGEN
Model: Touareg
Vehicle year: 2015
Bumper interface: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.
Product function: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.
Connector review: Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Fitting note: Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Selection context: Use the removed component as the physical reference for outer shape, housing projection and clip location.
Post-fit check: Check the opposite side as a reference for height, angle and edge gap before completing the repair.
Trade-order details: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
7P6 945 105A Rear Bumper Light Overview
This product is listed for VOLKSWAGEN Touareg 2015 at the left rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.
Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
For a repeat order of the left version, verify the fastener direction and the shape of the concealed support frame to avoid contact with wiring, body edges or hot exhaust components.
Vehicle-Specific Selection
Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.
Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
On the 2015 Touareg bumper layout, protect the visible surface until the full perimeter gap has been accepted to keep the optical face level with the surrounding painted surface.
At the workshop selection stage for Touareg, review the reflector texture and lens colour in neutral workshop light before any modification is made to the bumper or replacement part.
Passive Reflector or Lamp Configuration
Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
At the left rear-bumper position, record the approved side and vehicle application for repeat-order identification before deciding whether original hardware is suitable for reuse.
When reviewing the 2015 vehicle, confirm that the cable exit, where fitted, clears the bumper reinforcement because facelift bumpers can retain the same vehicle name with different apertures.
Fitting Guidance and Testing
Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
For the VOLKSWAGEN Touareg application, confirm that any connector seal remains square when the housing is fully seated so left- and right-hand stock cannot be mixed during consolidation.
For this Touareg body configuration, use the opposite-side component only as an alignment reference, not as an interchange part so the approved product can be picked consistently in a mixed wholesale order.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 7P6 945 105A |
| Cross-reference numbers | 7P6 945 105A |
| Internal item code | VM04004-012 |
| Vehicle brand | VOLKSWAGEN |
| Vehicle model | Touareg |
| Model year | 2015 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.
Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
Before approving the Touareg part for packing, compare the outer lens edge with the moulded bumper recess so hidden brackets are not loaded or bent during installation.
Before fitting the left unit, inspect the lower valance and nearby exhaust trim for adequate operating clearance to preserve access for a final electrical test where a lamp circuit is present.
Frequently Asked Questions
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
Request a Product-Specific Quote
Where the application is uncertain, send bumper-opening and rear-housing photographs for comparison first.
