92406-1Y800 Rear Bumper Light for KIA Picanto 2011-2017 Right
Primary OE reference: 92406-1Y800
Product type: Rear Bumper Light
Applicable vehicle: KIA Picanto 2011-2017
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: KIA
Model: Picanto
Vehicle year: 2011-2017
Housing match: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Reflector or lamp role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Wiring confirmation: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Mounting sequence: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.
Purchase information: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
92406-1Y800 Rear Bumper Light Overview
This product is listed for KIA Picanto 2011-2017 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
Use the removed component as the physical reference for outer shape, housing projection and clip location.
When reviewing the 2011-2017 vehicle, protect the visible surface until the full perimeter gap has been accepted to avoid contact with wiring, body edges or hot exhaust components.
Rear-Bumper Geometry Review
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
For the KIA Picanto application, review the reflector texture and lens colour in neutral workshop light to keep the optical face level with the surrounding painted surface.
For this Picanto body configuration, record the approved side and vehicle application for repeat-order identification before any modification is made to the bumper or replacement part.
Lens, Housing and Harness Comparison
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Protect the exposed face from tools and fasteners while the bumper liner is open for access.
Before approving the Picanto part for packing, confirm that the cable exit, where fitted, clears the bumper reinforcement before deciding whether original hardware is suitable for reuse.
Before fitting the right unit, confirm that any connector seal remains square when the housing is fully seated because facelift bumpers can retain the same vehicle name with different apertures.
Installation Completion
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.
While the KIA bumper opening is accessible, use the opposite-side component only as an alignment reference, not as an interchange part so left- and right-hand stock cannot be mixed during consolidation.
During comparison of the KIA rear component, compare the outer lens edge with the moulded bumper recess so the approved product can be picked consistently in a mixed wholesale order.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 92406-1Y800 |
| Cross-reference numbers | 92406-1Y800 |
| Internal item code | KA04004-024 |
| Vehicle brand | KIA |
| Vehicle model | Picanto |
| Model year | 2011-2017 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
For a repeat order of the right version, inspect the lower valance and nearby exhaust trim for adequate operating clearance so hidden brackets are not loaded or bent during installation.
On the 2011-2017 Picanto bumper layout, check the rear housing projection against the space behind the bumper skin to preserve access for a final electrical test where a lamp circuit is present.
Frequently Asked Questions
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Request a Product-Specific Quote
Clear application details allow the sales team to separate reflector and illuminated versions in the offer.
