81480-60030 Rear Bumper Light for TOYOTA Land Cruiser 2007 Left
Primary OE reference: 81480-60030
Product type: Rear Bumper Light
Applicable vehicle: TOYOTA Land Cruiser 2007
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: TOYOTA
Model: Land Cruiser
Vehicle year: 2007
Bumper interface: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.
Product function: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.
Connector review: Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Fitting note: Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: After installation, confirm the lens is level with nearby trim and that no retaining tab has backed out.
Trade-order details: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.
81480-60030 Rear Bumper Light Overview
This product is listed for TOYOTA Land Cruiser 2007 at the left rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
While the TOYOTA bumper opening is accessible, protect the visible surface until the full perimeter gap has been accepted before deciding whether original hardware is suitable for reuse.
Application and Rear-Bumper Position
Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
During comparison of the TOYOTA rear component, review the reflector texture and lens colour in neutral workshop light because facelift bumpers can retain the same vehicle name with different apertures.
For a repeat order of the left version, record the approved side and vehicle application for repeat-order identification so left- and right-hand stock cannot be mixed during consolidation.
Optical Face and Connector Review
Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
On the 2007 Land Cruiser bumper layout, confirm that the cable exit, where fitted, clears the bumper reinforcement so the approved product can be picked consistently in a mixed wholesale order.
At the workshop selection stage for Land Cruiser, confirm that any connector seal remains square when the housing is fully seated so hidden brackets are not loaded or bent during installation.
Workshop Fitting Sequence
Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.
At the left rear-bumper position, use the opposite-side component only as an alignment reference, not as an interchange part to preserve access for a final electrical test where a lamp circuit is present.
When reviewing the 2007 vehicle, compare the outer lens edge with the moulded bumper recess to reduce clip damage during a no-force trial installation.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 81480-60030 |
| Cross-reference numbers | 81480-60030 |
| Internal item code | TY04004-041 |
| Vehicle brand | TOYOTA |
| Vehicle model | Land Cruiser |
| Model year | 2007 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.
Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.
For the TOYOTA Land Cruiser application, inspect the lower valance and nearby exhaust trim for adequate operating clearance to prevent a visually similar version from sitting proud of the bumper.
For this Land Cruiser body configuration, check the rear housing projection against the space behind the bumper skin before the packaging and carton marking are finalized.
Frequently Asked Questions
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
Request a Product-Specific Quote
For mixed shipments, send a line-by-line quantity list so each rear-bumper position is quoted independently.
