81910-02180 Rear Bumper Light for TOYOTA Corolla 2014 Right
Primary OE reference: 81910-02180
Product type: Rear Bumper Light
Applicable vehicle: TOYOTA Corolla 2014
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: TOYOTA
Model: Corolla
Vehicle year: 2014
Fitment evidence: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.
Optical configuration: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Electrical interface: Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Final alignment: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
Bulk supply: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.
Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.
81910-02180 Rear Bumper Light Overview
This product is listed for TOYOTA Corolla 2014 at the right rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
When reviewing the 2014 vehicle, compare the bumper corner radius with the product face from more than one viewing angle before the packaging and carton marking are finalized.
Application and Rear-Bumper Position
Review the corner radius, edge return and rear fastening points against the original bumper opening.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
For the TOYOTA Corolla application, align each locating tab with the matching slot before applying hand pressure before inner liners make the rear attachment points difficult to inspect.
For this Corolla body configuration, check whether the original component uses a separate retainer or an integral locking tab so the visible gap remains even after every retaining point is engaged.
Optical Face and Connector Review
Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.
Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.
Before approving the Corolla part for packing, verify the fastener direction and the shape of the concealed support frame so the lens and housing are supported without distortion.
Before fitting the right unit, protect the visible surface until the full perimeter gap has been accepted so a passive reflector is not confused with an illuminated assembly.
Workshop Fitting Sequence
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
While the TOYOTA bumper opening is accessible, review the reflector texture and lens colour in neutral workshop light to verify that the photographed configuration matches the vehicle in the workshop.
During comparison of the TOYOTA rear component, record the approved side and vehicle application for repeat-order identification to avoid contact with wiring, body edges or hot exhaust components.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 81910-02180 |
| Cross-reference numbers | 81910-02180 |
| Internal item code | TY04004-025 |
| Vehicle brand | TOYOTA |
| Vehicle model | Corolla |
| Model year | 2014 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
For a repeat order of the right version, confirm that the cable exit, where fitted, clears the bumper reinforcement to keep the optical face level with the surrounding painted surface.
On the 2014 Corolla bumper layout, confirm that any connector seal remains square when the housing is fully seated before any modification is made to the bumper or replacement part.
Frequently Asked Questions
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
Is this component illuminated or reflector-only?
Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
Request a Product-Specific Quote
Clear application details allow the sales team to separate reflector and illuminated versions in the offer.
