34270-TFC-H01 Rear Bumper Light for HONDA CR-V 2015
Primary OE reference: 34270-TFC-H01
Product type: Rear Bumper Light
Applicable vehicle: HONDA CR-V 2015
Installation position: Rear bumper / reflector opening
Side / orientation: Confirm by original part
Brand: HONDA
Model: CR-V
Vehicle year: 2015
Physical comparison: Review the corner radius, edge return and rear fastening points against the original bumper opening.
Lighting function: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.
Electrical check: Confirm separately whether the removed component uses wiring, a bulb holder or an integrated LED module.
Installation guidance: Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Post-fit check: Check the opposite side as a reference for height, angle and edge gap before completing the repair.
Wholesale enquiry: Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.
Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.
34270-TFC-H01 Rear Bumper Light Overview
This product is listed for HONDA CR-V 2015 at the confirm by original part rear-bumper position. This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.
For the HONDA CR-V application, review the reflector texture and lens colour in neutral workshop light to prevent a visually similar version from sitting proud of the bumper.
Application and Rear-Bumper Position
Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.
Production date and regional bumper specification should be reviewed when several near-identical versions are available.
For this CR-V body configuration, record the approved side and vehicle application for repeat-order identification before the packaging and carton marking are finalized.
Before approving the CR-V part for packing, confirm that the cable exit, where fitted, clears the bumper reinforcement before inner liners make the rear attachment points difficult to inspect.
Optical Face and Connector Review
Confirm separately whether the removed component uses wiring, a bulb holder or an integrated LED module.
Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.
Before fitting the confirm by original part unit, confirm that any connector seal remains square when the housing is fully seated so the visible gap remains even after every retaining point is engaged.
While the HONDA bumper opening is accessible, use the opposite-side component only as an alignment reference, not as an interchange part so the lens and housing are supported without distortion.
Workshop Fitting Sequence
Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
During comparison of the HONDA rear component, compare the outer lens edge with the moulded bumper recess so a passive reflector is not confused with an illuminated assembly.
For a repeat order of the confirm by original part version, inspect the lower valance and nearby exhaust trim for adequate operating clearance to verify that the photographed configuration matches the vehicle in the workshop.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 34270-TFC-H01 |
| Cross-reference numbers | 34270-TFC-H01 |
| Internal item code | HD04004-074 |
| Vehicle brand | HONDA |
| Vehicle model | CR-V |
| Model year | 2015 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Confirm by original part |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.
The visible face should remain separated from tape, staples and loose hardware throughout transport.
On the 2015 CR-V bumper layout, check the rear housing projection against the space behind the bumper skin to avoid contact with wiring, body edges or hot exhaust components.
At the workshop selection stage for CR-V, compare the bumper corner radius with the product face from more than one viewing angle to keep the optical face level with the surrounding painted surface.
Frequently Asked Questions
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
Which physical points matter most?
Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Is this component illuminated or reflector-only?
Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.
Request a Product-Specific Quote
Yongshang Auto can review the pictured configuration before preparing a quantity-based offer.
