33505-S9A-003 Rear Bumper Light for HONDA CR-V 2003 Right
Primary OE reference: 33505-S9A-003
Product type: Rear Bumper Light
Applicable vehicle: HONDA CR-V 2003
Installation position: Rear bumper / reflector opening
Side / orientation: Right
Brand: HONDA
Model: CR-V
Vehicle year: 2003
Housing match: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.
Reflector or lamp role: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.
Wiring confirmation: Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Mounting sequence: Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Selection context: Use the removed component as the physical reference for outer shape, housing projection and clip location.
Post-fit check: Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.
Purchase information: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
33505-S9A-003 Rear Bumper Light Overview
This product is listed for HONDA CR-V 2003 at the right rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.
Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.
For this CR-V body configuration, confirm that the cable exit, where fitted, clears the bumper reinforcement before the packaging and carton marking are finalized.
Vehicle-Specific Selection
Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.
Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.
Before approving the CR-V part for packing, confirm that any connector seal remains square when the housing is fully seated before inner liners make the rear attachment points difficult to inspect.
Before fitting the right unit, use the opposite-side component only as an alignment reference, not as an interchange part so the visible gap remains even after every retaining point is engaged.
Passive Reflector or Lamp Configuration
Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.
Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.
While the HONDA bumper opening is accessible, compare the outer lens edge with the moulded bumper recess so the lens and housing are supported without distortion.
During comparison of the HONDA rear component, inspect the lower valance and nearby exhaust trim for adequate operating clearance so a passive reflector is not confused with an illuminated assembly.
Fitting Guidance and Testing
Check the mounting direction and side before installation; left and right components are not automatically interchangeable.
Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.
For a repeat order of the right version, check the rear housing projection against the space behind the bumper skin to verify that the photographed configuration matches the vehicle in the workshop.
On the 2003 CR-V bumper layout, compare the bumper corner radius with the product face from more than one viewing angle to avoid contact with wiring, body edges or hot exhaust components.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 33505-S9A-003 |
| Cross-reference numbers | 33505-S9A-003 |
| Internal item code | HD04004-064 |
| Vehicle brand | HONDA |
| Vehicle model | CR-V |
| Model year | 2003 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Right |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
At the workshop selection stage for CR-V, align each locating tab with the matching slot before applying hand pressure to keep the optical face level with the surrounding painted surface.
At the right rear-bumper position, check whether the original component uses a separate retainer or an integral locking tab before any modification is made to the bumper or replacement part.
Frequently Asked Questions
Can the opposite side use the same part?
Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.
How is a passive reflector checked?
Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Should original clips be reused?
Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
Request a Product-Specific Quote
Provide the expected order quantity to receive a trade-oriented packing and supply proposal.
