81920-13022 Rear Bumper Light for TOYOTA RAV4 2006-2008 Left
Primary OE reference: 81920-13022
Product type: Rear Bumper Light
Applicable vehicle: TOYOTA RAV4 2006-2008
Installation position: Rear bumper / reflector opening
Side / orientation: Left
Brand: TOYOTA
Model: RAV4
Vehicle year: 2006-2008
Housing match: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.
Reflector or lamp role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.
Wiring confirmation: For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Mounting sequence: Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Selection context: The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.
Purchase information: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.
Packing reference: Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
81920-13022 Rear Bumper Light Overview
This product is listed for TOYOTA RAV4 2006-2008 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
At the workshop selection stage for RAV4, review the reflector texture and lens colour in neutral workshop light before deciding whether original hardware is suitable for reuse.
Bumper Opening and Vehicle Match
Review the corner radius, edge return and rear fastening points against the original bumper opening.
The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.
At the left rear-bumper position, record the approved side and vehicle application for repeat-order identification because facelift bumpers can retain the same vehicle name with different apertures.
When reviewing the 2006-2008 vehicle, confirm that the cable exit, where fitted, clears the bumper reinforcement so left- and right-hand stock cannot be mixed during consolidation.
Lens Construction and Powered Variants
For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.
Protect the exposed face from tools and fasteners while the bumper liner is open for access.
For the TOYOTA RAV4 application, confirm that any connector seal remains square when the housing is fully seated so the approved product can be picked consistently in a mixed wholesale order.
For this RAV4 body configuration, use the opposite-side component only as an alignment reference, not as an interchange part so hidden brackets are not loaded or bent during installation.
Mounting and Final Verification
Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.
Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.
Before approving the RAV4 part for packing, compare the outer lens edge with the moulded bumper recess to preserve access for a final electrical test where a lamp circuit is present.
Before fitting the left unit, inspect the lower valance and nearby exhaust trim for adequate operating clearance to reduce clip damage during a no-force trial installation.
Automotive Lighting Product Specifications
| Product type | Rear Bumper Light |
|---|---|
| Primary OE reference | 81920-13022 |
| Cross-reference numbers | 81920-13022 |
| Internal item code | TY04004-005 |
| Vehicle brand | TOYOTA |
| Vehicle model | RAV4 |
| Model year | 2006-2008 |
| Installation position | Rear bumper / reflector opening |
| Side / orientation | Left |
| Configuration | Match the photographed reflector or powered-lamp version |
Wholesale Supply and Protective Packing
For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.
Before sealing the carton, compare the packed side and quantity with the buyer’s order line.
While the TOYOTA bumper opening is accessible, check the rear housing projection against the space behind the bumper skin to prevent a visually similar version from sitting proud of the bumper.
During comparison of the TOYOTA rear component, compare the bumper corner radius with the product face from more than one viewing angle before the packaging and carton marking are finalized.
Frequently Asked Questions
When should photographs be supplied?
Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.
Can appearance alone confirm compatibility?
No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.
What if the bumper opening differs?
Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.
How should the visible lens be packed?
Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.
What details help with a wholesale quote?
Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.
Request a Product-Specific Quote
Repeat buyers can reference the vehicle application and side from their previous approved sample.
