4H0955102C Front Right Headlight Washer Nozzle for AUDI A8 2016

4H0955102C Front Right Headlight Washer Nozzle Product Overview

The component shown under 4H0955102C is a front right headlight washer nozzle intended for AUDI A8 2016. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the right orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A8

Compatibility for 4H0955102C should be confirmed against AUDI A8 2016 and the right installation side. The review should confirm whether a cap, nozzle, bracket or complete assembly is required, check regional variations in headlamp-cleaning equipment, and compare every tab, clip seat and locating shoulder. Use the removed part and product photographs to check the washer jet position relative to the headlamp lens, match the exact model year and bumper revision, and confirm the destination-market equipment specification; finally, confirm whether a cap, nozzle, bracket or complete assembly is required and check regional variations in headlamp-cleaning equipment.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-072 should be checked separately. For this headlight washer nozzle, inspect narrow plastic tips before installation, compare the support flange width, and review any paint-preparation requirement before fitting. A direct comparison with the removed part should additionally check the nozzle outlet orientation, inspect the rear reinforcement ribs, and compare the cap perimeter and corner radii. Before the item is accepted, review the hose spigot angle on the washer nozzle and check the fluid inlet for storage contamination.

OE Identification and Side Confirmation

4H0955102C is the primary OE identity for this right front right headlight washer nozzle, while AD02010-072 is the internal item code. Match both references to the vehicle record, then confirm that the vehicle is equipped with a factory headlight washer system. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-072 begins before the bumper area is disturbed: follow the vehicle workshop procedure for bumper removal and inspect the bumper opening after the trial fit. During trial fitting, check the system for leaks after reconnection, check that the washer unit is fully seated in its guide, and work with the washer system depressurized. Before returning the vehicle to service, support the bumper cover while accessing the hidden actuator, test for drips after the washer pump stops, and align the cover flush with the bumper surface.

Receiving Inspection

When AD02010-072 arrives, receiving staff should check molded tabs for whitening, cracks or transport stress, confirm the nozzle outlet is clean and unobstructed, and review the hose spigot for impact damage or distortion. Before workshop release, compare left and right orientation before removing protective wrapping, verify the cover contour against the approved product photograph, check the spring-return area where the component includes an actuator, and inspect the rear locator shape without forcing any movable section. Complete the inspection by ensuring that staff confirm that loose accessories are identified on the packing list, record carton damage before the item is moved to workshop stock, and check painted or primed surfaces under neutral lighting.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4H0955102C, please request a packing-list breakdown by internal item code, list model years and bumper versions for mixed orders, and request replacement-part documentation when required. Packing instructions should identify project stock and service stock separately, state the required order quantity, and confirm the preferred incoterm. Before dispatch, identify the required installation side and state the requested delivery schedule.

Frequently Asked Questions

Which vehicle application is listed for 4H0955102C?

4H0955102C is listed for AUDI A8 2016. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. For item AD02010-072, the approval should compare the actuator orientation behind the bumper cover. The same item record should also confirm the destination-market equipment specification.

What information should accompany a 4H0955102C enquiry?

Send the complete OE number, vehicle model and year, installation side, original-part photographs, quantity and delivery destination. On the listed AUDI A8 2016, technicians should plug open fluid connections during packing. A workshop comparison should additionally confirm whether caps and nozzles should be supplied as pairs.

Is a sample order available for 4H0955102C?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For the right-side order line, state the target vehicle application. The order review should further use dividers to prevent caps from rubbing each other.

Are clips, hoses or fasteners supplied with 4H0955102C?

The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. The product-specific check for 4H0955102C should confirm the acceptable delivery window. Receiving staff should also separate left and right items on the packing list.

Should the washer system be tested after fitting 4H0955102C?

Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. Before this headlight washer nozzle is accepted, tighten bracket hardware only after alignment. Before approval, the buyer or technician should verify that the cover closes without rubbing the bumper.