4H0955101C Front Left Headlight Washer Nozzle for AUDI A8 2016

4H0955101C Front Left Headlight Washer Nozzle Product Overview

The component shown under 4H0955101C is a front left headlight washer nozzle intended for AUDI A8 2016. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A8

Compatibility for 4H0955101C should be confirmed against AUDI A8 2016 and the left installation side. The review should review facelift and pre-facelift washer layouts, match the mounting pattern around the bumper aperture, and retain the removed component for a direct physical comparison. Use the removed part and product photographs to verify that the OE reference is not for the opposite side, check regional variations in headlamp-cleaning equipment, and match the connector and fluid inlet position where applicable; finally, check whether the original cover is supplied separately from its support and confirm the front bumper option before ordering.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-071 should be checked separately. For this headlight washer nozzle, compare the outer surface profile with the bumper opening, inspect narrow plastic tips before installation, and check the bumper-facing surface for transport marks. A direct comparison with the removed part should additionally review the bracket stiffness and screw seats, compare the visible bumper-side contour, and inspect the base bracket around every locating slot. Before the item is accepted, check whether the visible part requires painting and review the engagement of the cover with the nozzle stem.

OE Identification and Side Confirmation

4H0955101C is the primary OE identity for this left front left headlight washer nozzle, while AD02010-071 is the internal item code. Match both references to the vehicle record, then check regional variations in headlamp-cleaning equipment. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-071 begins before the bumper area is disturbed: test the spray direction before returning the vehicle and paint or finish visible covers before final installation when required. During trial fitting, retain the original fasteners unless replacements are specified, check the system for leaks after reconnection, and inspect nearby wiring and sensors before refitting trim. Before returning the vehicle to service, confirm that no hose is pinched behind the bumper, confirm that the nozzle extends and retracts freely, and confirm sufficient clearance behind the bumper.

Receiving Inspection

When AD02010-071 arrives, receiving staff should document any shortage before the receiving inspection is closed, separate mirrored components immediately after carton opening, and check the spring-return area where the component includes an actuator. Before workshop release, verify the nozzle head returns smoothly without applying excess force, check the cap hinge or retaining point for free movement, inspect the rear locator shape without forcing any movable section, and inspect the fluid passage only with clean, non-damaging tools. Complete the inspection by ensuring that staff verify that protective plugs remain in open fluid connections, confirm that loose accessories are identified on the packing list, and compare the supplied side with the vehicle repair order.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 4H0955101C, please confirm the preferred incoterm, send photographs of the removed washer part, and confirm the preferred incoterm. Packing instructions should send photographs of the removed washer part, confirm the preferred incoterm, and send photographs of the removed washer part. Before dispatch, confirm the preferred incoterm and send photographs of the removed washer part.

Frequently Asked Questions

Is a sample order available for 4H0955101C?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. For item AD02010-071, the approval should confirm sample approval before mass shipment. The same item record should also request moisture protection for sea freight.

Can product photographs alone confirm 4H0955101C compatibility?

Photographs are useful for visual comparison, but the full OE number, vehicle year, bumper version, side and washer equipment must also match. On the listed AUDI A8 2016, technicians should retain the removed component for a direct physical comparison. A workshop comparison should additionally inspect the bumper cutout shape and surrounding contour.

Is workshop installation recommended for 4H0955101C?

Yes. A qualified workshop can access the bumper area on the A8, transfer hoses or clips safely and test the washer system for correct operation and leaks. For the left-side order line, inspect nearby wiring and sensors before refitting trim. The order review should further verify that the cover closes without rubbing the bumper.

Why must left and right versions of 4H0955101C be distinguished?

Headlight washer components are normally side-specific. Their bumper contours, hose angles, tabs and nozzle directions should not be assumed interchangeable. The product-specific check for 4H0955101C should compare the retracted position with the bumper surface. Receiving staff should also check the nozzle outlet orientation.

Does the finish specification matter for 4H0955101C?

Yes. A visible headlight washer nozzle may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. Before this headlight washer nozzle is accepted, compare the outer surface profile with the bumper opening. Before approval, the buyer or technician should check the joint between the visible cap and hidden support.