8T0955101D Front Left Headlight Washer Nozzle for AUDI A5 2013

8T0955101D Front Left Headlight Washer Nozzle Product Overview

The component shown under 8T0955101D is a front left headlight washer nozzle intended for AUDI A5 2013. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A5

Compatibility for 8T0955101D should be confirmed against AUDI A5 2013 and the left installation side. The review should confirm whether a cap, nozzle, bracket or complete assembly is required, check regional variations in headlamp-cleaning equipment, and compare every tab, clip seat and locating shoulder. Use the removed part and product photographs to check the washer jet position relative to the headlamp lens, match the exact model year and bumper revision, and confirm the destination-market equipment specification; finally, confirm whether a cap, nozzle, bracket or complete assembly is required and check regional variations in headlamp-cleaning equipment.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-037 should be checked separately. For this headlight washer nozzle, review the bracket stiffness and screw seats, check the cap hinge or retaining point, and inspect narrow plastic tips before installation. A direct comparison with the removed part should additionally compare the support flange width, review any paint-preparation requirement before fitting, and check the nozzle outlet orientation. Before the item is accepted, inspect the rear reinforcement ribs and compare the cap perimeter and corner radii.

OE Identification and Side Confirmation

8T0955101D is the primary OE identity for this left front left headlight washer nozzle, while AD02010-037 is the internal item code. Match both references to the vehicle record, then confirm that the vehicle is equipped with a factory headlight washer system. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-037 begins before the bumper area is disturbed: avoid forcing a mirrored part into the bumper opening and reconnect every hose clip before filling the system. During trial fitting, disconnect the fluid hose without twisting the plastic spigot, tighten bracket hardware only after alignment, and photograph the original routing before disassembly. Before returning the vehicle to service, confirm that the nozzle extends and retracts freely, paint or finish visible covers before final installation when required, and reconfirm the OE number before discarding the packaging.

Receiving Inspection

When AD02010-037 arrives, receiving staff should verify the nozzle head returns smoothly without applying excess force, inspect the fluid passage only with clean, non-damaging tools, and compare the supplied side with the vehicle repair order. Before workshop release, protect the visible face again after inspection is complete, match the item label to the purchase order and OE reference, inspect the visible cover face for scratches or pressure marks, and check molded tabs for whitening, cracks or transport stress. Complete the inspection by ensuring that staff confirm the nozzle outlet is clean and unobstructed, review the hose spigot for impact damage or distortion, and compare left and right orientation before removing protective wrapping.

Product Technical Specifications

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8T0955101D, please provide the consignee and freight-forwarder details, confirm whether the visible cover needs a primed or finished surface, and separate fragile actuator bodies from heavier metal parts. Packing instructions should protect hose spigots and projecting tabs, state any outer-carton marking requirements, and state the target vehicle application. Before dispatch, identify painted and unpainted variants on separate lines and check carton labels at receiving.

Frequently Asked Questions

Why must left and right versions of 8T0955101D be distinguished?

Headlight washer components are normally side-specific. Their bumper contours, hose angles, tabs and nozzle directions should not be assumed interchangeable. For item AD02010-037, the approval should compare the depth of the actuator body. The same item record should also check the nozzle outlet orientation.

Is a sample order available for 8T0955101D?

Sample and wholesale arrangements can be discussed after the OE reference, application, side, quantity and shipping destination are provided. On the listed AUDI A5 2013, technicians should use dividers to prevent caps from rubbing each other. A workshop comparison should additionally state the requested delivery schedule.

Does the finish specification matter for 8T0955101D?

Yes. A visible headlight washer nozzle may be primed, painted or textured for a specific bumper version. Compare the original surface and colour requirements before installation. For the left-side order line, check the cap hinge or retaining point. The order review should further check the nozzle outlet orientation.

Should the washer system be tested after fitting 8T0955101D?

Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. The product-specific check for 8T0955101D should avoid forcing a mirrored part into the bumper opening. Receiving staff should also verify that the cap remains attached through a full washer cycle.

How should 8T0955101D be packed for export?

The front left headlight washer nozzle should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. Before this headlight washer nozzle is accepted, confirm the acceptable delivery window. Before approval, the buyer or technician should check carton labels at receiving.