71140-T2A-A01 Front Right Headlight Mounting Bracket for HONDA Accord 2014

71140-T2A-A01 Front Right Headlight Mounting Bracket Product Overview

The component shown under 71140-T2A-A01 is a front right headlight mounting bracket intended for HONDA Accord 2014. Confirm the right orientation, lamp-side contour, mounting geometry against the original vehicle part.

Fitment and Application for Accord

When reviewing the visible finish on HD02009-006, compare the installation direction, match the accessory to the original bumper revision, and compare every locating point and screw opening. For a no-force trial fit, check nearby body-panel interfaces, review headlamp shape changes between production phases, and verify the left or right mounting side.

Before sourcing this front right headlight mounting bracket, compare the stamped or moulded reference, review the orientation of the moulded bracket, and review regional specification differences. While checking adjacent body parts, check whether the original part is mirrored, compare adjacent bumper and grille sections, and match the body style and equipment grade.

Before confirming this headlight accessory, compare the complete OE marking with the removed part, review regional specification differences, and compare every locating point and screw opening. Before the quotation is confirmed, review facelift and pre-facelift styling, compare adjacent bumper and grille sections, and check nearby body-panel interfaces.

Headlight Mounting Bracket Design and Replacement Notes

For replacement in the right front headlamp area, inspect moulded corners before installation, inspect reinforcement features behind the part, and inspect the junction with the fender edge. When organizing mixed-OE inventory, compare reusable clips and hardware, review the distance between fastening points, and check the interface with the lamp housing.

When separating nearby Accord variants, review the distance between fastening points, inspect the visible face for transport scuffing, and inspect the moulded front face and rear ribs. While reviewing the supplied photographs, compare the original edge profile, review the direction of the locating tabs, and check the curvature beside the headlamp.

When reviewing the visible finish on HD02009-006, compare the centre alignment point, measure the removed part where references are unclear, and check mirrored geometry against the required side. Before final installation, inspect the moulded front face and rear ribs, inspect reinforcement features behind the part, and inspect the overall frame width.

Application-Specific Identification

OE identification begins with 71140-T2A-A01 on the Accord 2014: verify the left or right mounting side. The HD02009-006 sample for the right side should inspect reinforcement features behind the part. Before installation, check that no locator is trapped behind the bumper; for a quotation, review edge protection inside the carton.

A vehicle-side comparison starts with 71140-T2A-A01 on the Accord 2014: verify the left or right mounting side. The HD02009-006 sample for the right side should check mirrored geometry against the required side. Before installation, protect exposed edges during removal; for a quotation, request the applicable export terms.

Before a replacement is packed with 71140-T2A-A01 on the Accord 2014: review facelift and pre-facelift styling. The HD02009-006 sample for the right side should check the adjoining panel gap. Before installation, keep the removed part nearby for comparison; for a quotation, agree the acceptable delivery window.

Installation Guidance

For wholesale selection of 71140-T2A-A01, verify that the headlamp remains centred, inspect broken vehicle-side mounts, and route nearby wiring away from sharp edges. When checking the headlamp opening, keep the removed part nearby for comparison, inspect the lamp aim after surrounding parts are refitted, and review whether separate hardware is needed.

During left-versus-right inventory selection, check that no locator is trapped behind the bumper, reconfirm the OE reference after the trial fit, and align the headlamp edge before fastening. Before the carton is sealed, check lamp-to-trim clearance, review completed left-to-right alignment, and replace distorted clips before final assembly.

For replacement in the right front headlamp area, check the finish for tool marks before delivery, confirm the correct fitting direction, and use hand pressure only during the initial engagement. Before clips or hardware are transferred, keep the removed part nearby for comparison, check that no locator is trapped behind the bumper, and check the adjoining panel gaps.

Product Technical Specifications

Wholesale Supply and Packing

Before confirming export packing for 71140-T2A-A01, identify mixed-OE orders clearly, confirm barcode or private-label requirements, and ask for carton dimensions before freight booking. Before the quotation is confirmed, request moisture protection for sea freight, separate painted and unpainted variants, and check sample approval before mass shipment.

During an OE-led review for HD02009-006, ask for carton dimensions before freight booking, provide the destination country, and compare the supplied product photographs. Before packing the confirmed item, provide the consignee contact information, confirm replacement-part documentation needs, and review edge protection inside the carton.

For wholesale selection of 71140-T2A-A01, separate painted and unpainted variants, check the ordered mounting side, and confirm the nominated freight forwarder. For an application-specific order, state estimated annual purchasing volume, request a packing-list breakdown by item code, and request the applicable export terms.

Frequently Asked Questions

Which vehicle application is listed for 71140-T2A-A01?

71140-T2A-A01 is listed for HONDA Accord 2014. The complete OE reference, production year, body specification and mounting side should agree with the removed component. For Accord, review headlamp shape changes between production phases; check the curvature beside the headlamp; verify that no fastener is cross-threaded; and ask for carton dimensions before freight booking before fitting or quotation.

How should 71140-T2A-A01 be packed for export?

The front right headlight mounting bracket should be supported inside the carton, with projecting tabs, narrow ends and visible surfaces protected against abrasion and compression. For Accord, review regional specification differences; inspect the visible face for transport scuffing; confirm that the hood and fender clearances remain even; and protect projecting locator tabs before fitting or quotation.

Is a sample order available for 71140-T2A-A01?

Sample and wholesale arrangements can be discussed after the OE reference, vehicle application, required side, quantity and destination are provided. For Accord, check the vehicle production date where available; inspect the junction with the fender edge; route nearby wiring away from sharp edges; and specify whether the order is for service stock or a project before fitting or quotation.

What information should be sent with a 71140-T2A-A01 enquiry?

Send the complete OE number, vehicle details, installation side, photographs of the original part, quantity and delivery destination. For Accord, inspect the original lamp-support geometry; check mirrored geometry against the required side; complete a visual check under even lighting; and provide the destination country before fitting or quotation.

Should damaged vehicle-side mounts be checked before fitting 71140-T2A-A01?

Yes. Broken lamp tabs, distorted bumper guides or missing retainers can prevent correct alignment even when the replacement reference is correct. For Accord, check the lamp manufacturer where multiple units were fitted; inspect the overall frame width; confirm a consistent bumper gap; and state the destination port or city before fitting or quotation.

Request a Quote

Send the complete OE reference 71140-T2A-A01, vehicle details, installation side, required quantity and delivery destination. Yongshang Auto can review the application before preparing a product-specific export quotation.