71190-SNA-A00 Front Left Headlight Mounting Bracket for HONDA Civic 2006

71190-SNA-A00 Front Left Headlight Mounting Bracket Product Overview

The component shown under 71190-SNA-A00 is a front left headlight mounting bracket intended for HONDA Civic 2006. Confirm the left orientation, lamp-side contour, mounting geometry against the original vehicle part.

Fitment and Application for Civic

Before confirming this headlight accessory, verify the left or right mounting side, verify the trim package named in the application, and review facelift and pre-facelift styling. Before the quotation is confirmed, match the accessory to the original bumper revision, confirm the decorative finish or painted surface, and match the body style and equipment grade.

For a body-shop order covering HONDA, match the outer profile around the headlamp, check the vehicle production date where available, and compare adjacent bumper and grille sections. Before packing the confirmed item, review the orientation of the moulded bracket, confirm the decorative finish or painted surface, and check nearby body-panel interfaces.

When comparing 71190-SNA-A00 with the removed component, match the locator-slot arrangement, confirm whether the vehicle uses a special appearance package, and retain the original component for a direct comparison. For an application-specific order, confirm the decorative finish or painted surface, compare the stamped or moulded reference, and review regional specification differences.

Headlight Mounting Bracket Design and Replacement Notes

When reviewing the visible finish on HD02009-029, compare reusable clips and hardware, review the direction of the locating tabs, and inspect moulded corners before installation. Before final installation, measure the removed part where references are unclear, check the curvature beside the headlamp, and review the thickness around each mounting boss.

Before sourcing this front left headlight mounting bracket, inspect the overall frame width, compare the profile below the lamp lens, and compare the original edge profile. At the workshop preparation stage, compare the visible texture and finish, check the interface with the lamp housing, and check mirrored geometry against the required side.

Before confirming this headlight accessory, review the thickness around each mounting boss, review narrow tips for transport damage, and check the depth of the moulded locator channels. For a repeat wholesale purchase, measure the removed part where references are unclear, inspect the visible face for transport scuffing, and review nearby cover openings.

Application-Specific Identification

At receiving inspection with 71190-SNA-A00 on the Civic 2006: confirm the decorative finish or painted surface. The HD02009-029 sample for the left side should check the adjoining panel gap. Before installation, confirm that the hood and fender clearances remain even; for a quotation, confirm sample-order requirements.

For application-specific sourcing with 71190-SNA-A00 on the Civic 2006: confirm the front installation position. The HD02009-029 sample for the left side should inspect the overall frame width. Before installation, keep the removed part nearby for comparison; for a quotation, retain the product and carton labels.

At receiving inspection with 71190-SNA-A00 on the Civic 2006: check the relationship with the lamp housing. The HD02009-029 sample for the left side should compare the original edge profile. Before installation, clean the lamp and bumper mounting area; for a quotation, request corner protection for long moulded parts.

Installation Guidance

For replacement in the left front headlamp area, check the final perimeter around the lamp, inspect the surrounding guides, and tighten hardware only after alignment. Before clips or hardware are transferred, replace distorted clips before final assembly, reinstall removed seals in their original positions, and inspect the lamp aim after surrounding parts are refitted.

When separating nearby Civic variants, tighten hardware only after alignment, photograph the completed installation for order records, and check lamp-to-trim clearance. At the alignment stage, compare the installed height with the opposite side, clean the lamp and bumper mounting area, and confirm the correct fitting direction.

When reviewing the visible finish on HD02009-029, reinstall removed seals in their original positions, inspect each screw or clip point, and check the finish for tool marks before delivery. For a no-force trial fit, confirm an evenly seated fit, support adjacent body panels evenly, and tighten hardware only after alignment.

Product Technical Specifications

Wholesale Supply and Packing

For wholesale selection of 71190-SNA-A00, separate left and right items in the packing list, list every OE reference on the purchase order, and confirm replacement-part documentation needs. For an application-specific order, inspect the carton at receiving, request the applicable export terms, and confirm barcode or private-label requirements.

During left-versus-right inventory selection, state whether left and right pairs should be bundled, protect projecting locator tabs, and request corner protection for long moulded parts. During receiving inspection, include the complete OE reference, separate left and right items in the packing list, and state the required order quantity.

For replacement in the left front headlamp area, state any outer-carton marking requirements, request a packing-list breakdown by item code, and confirm replacement-part documentation needs. When organizing mixed-OE inventory, send photographs of the removed component, request supported export-carton packing, and inspect the carton at receiving.

Frequently Asked Questions

Which side uses 71190-SNA-A00?

This front left headlight mounting bracket is catalogued for the left front headlamp area. Opposite-side parts normally use mirrored geometry and a different reference. For Civic, check whether the original part is mirrored; inspect the moulded front face and rear ribs; transfer reusable clips carefully; and check the ordered mounting side before fitting or quotation.

What should be inspected when 71190-SNA-A00 arrives?

Check the item label, contour, finish, locating features, mounting points and carton condition before fitting or discarding the packaging. For Civic, verify the left or right mounting side; check the transition to the bumper or grille; support adjacent body panels evenly; and send photographs of the removed component before fitting or quotation.

Which vehicle application is listed for 71190-SNA-A00?

71190-SNA-A00 is listed for HONDA Civic 2006. The complete OE reference, production year, body specification and mounting side should agree with the removed component. For Civic, check nearby body-panel interfaces; inspect the back-side support structure; check the finish for tool marks before delivery; and confirm the preferred incoterm before fitting or quotation.

How should 71190-SNA-A00 be packed for export?

The front left headlight mounting bracket should be supported inside the carton, with projecting tabs, narrow ends and visible surfaces protected against abrasion and compression. For Civic, match the accessory to the original bumper revision; compare surrounding grille openings; reinstall removed seals in their original positions; and request the applicable export terms before fitting or quotation.

Is a sample order available for 71190-SNA-A00?

Sample and wholesale arrangements can be discussed after the OE reference, vehicle application, required side, quantity and destination are provided. For Civic, confirm the front installation position; compare gloss level with the neighbouring trim; complete a visual check under even lighting; and confirm the required finish before fitting or quotation.

Request a Quote

Send the complete OE reference 71190-SNA-A00, vehicle details, installation side, required quantity and delivery destination. Yongshang Auto can review the application before preparing a product-specific export quotation.